background image

 

Installation and Operation Manual 

Argos - Pressure Regulating Valve 

MI-23

 

 

Elaborado 

Verificado / Aprovado 

CSQ 

Data 

Revisão 

Página 

JJ 

 

VBL 

JM 

13/02/19 

07 

5 de 32 

 

ND 

FLANGE ASME B16.5 

FLANGE DIN 2634 / 2635 

1” 

150#RF / 300#RF 

(Thread NPT Female only for 1’’) 

PN 25 / PN 40 

2” 

150#RF / 300#RF 

PN 25 / PN 40 

3” 

150#RF / 300#RF 

PN 25 / PN 40 

4” 

150#RF / 300#RF 

PN 25 / PN 40 

 
Note: other diameters and connections should be previously consulted.

 

2.3.3 TEMPERATURE LIMITS 

Operation temperature: -20°C to 60°C 
 
Room temperature: -20°C to 60°C 
 
The temperature limits given in this manual or in any applicable standard shall not be exceeded under any 

circumstances, under risk of damage to the equipment, to the installation safety, and to the people involved in the 
operation. 

2.3.4 COEFFICIENT OF FLOW (CV) 

ND 

CV 

KG 

1” 

13.5 

420 

2” 

48 

1500 

3” 

93 

2900 

4” 

206 

6400 

NOTE:  
1) We suggest considering a 20% safety margin on the calculated value. 
2) When dimensioning an active-monitor system consider a 25% restriction in the CV/KG of both valves. 

2.3.5 WEIGHTS 

 

ND 

ARGOS 

ARGOS SSV 

150# 

300# 

150# 

300# 

1” 

11 

11.5 

2” 

15 

16 

30 

31 

3” 

28 

29 

43 

44 

4” 

42 

44 

58 

60 

 
NOTE:  
1) Approximate weights given in kilograms (Kg) 
2) Consider the body in carbon steel SA-216 WCB 
 

2.3.6 MAXIMUM WORK PRESSURE  

Summary of Contents for ARGOS

































Reviews: