background image

 

Installation and Operation Manual 

Argos - Pressure Regulating Valve 

MI-23

 

 

Elaborado 

Verificado / Aprovado 

CSQ 

Data 

Revisão 

Página 

JJ 

 

VBL 

JM 

13/02/19 

07 

23 de 32 

 

Note:  the  values  informed  in  the  table  above  are  recommendations  based  on  good  practices;  however,  the  set 
points can be changed if previously consulted and approved by GASCAT Engineering. 
 

4.6.6 COMMISSIONING (WORKING MONITOR SYSTEM) 

Utilizing  as  reference  the  assemblage  scheme  presented  on  item  4.5.4  proceed  with  descriptive  indicate  for 
commissioning of ARGOS pressure regulators in a stream where the configuration is working monitor, considering 
that the recommendations realized in the item 4.6.1 were totally observed. 
The procedure considers utilization of slam shut valve model GIPS-FC and pressure regulator model ARGOS. 
 

1)  Close the vent valve. 

As  the  ball  valves  of  skid  are  closed  utilize  the  vent  valve  to  simulate  a  low  flow  and  then  proceed  with 
adjustment of pressure regulator. 

2)  With the line still pressurized turn clockwise the regulating spring of pilot of second stage pressure regulator; 

and  counter-clockwise  the  spring  of  override  (extra)  pilot  of  the  regulator  of  first  stage.  It  will  make  the 
regulator remain in the closed position. 

3)  Verify if the restrictor installed in the inlet of pilot is open around 30%~70%. 
4)  Open SLOW  AND GRADUALLY the inlet ball valve or when the skid has by-pass utilize it to pressurize the 

line. 

5)  Since there is no pressure downstream the regulator the slam shut model GIPS-FC is closed. So that, press 

the  by-pass  or  push  button  of  slam  shut  valve  to  pressurize  the  line  between  the  slam  shut  and  pressure 
regulator. 

6)  Still using the by-pass or push button of SSV turn clockwise the regulating spring of monitor regulator to admit 

a small pressure downstream of both regulators. Use the pressure gauge to check it and adjust the regulator 
at least 20% above set point of under shut down of SSV. 

7)  As the actuator is already pressurized release the by-pass or push button and reset the actuator. 
8)  Reset the obturator of slam shut valve model GIPS-FC using the respective lever. 
9)  Open the vent valve 20% and check if the pressure is still the same. 
10) Turning clockwise the regulating spring of override (extra) pilot of first stage pressure regulator to increase the 

set point up to desired value. 
In this case, only the first stage pressure regulator will be in operation. 

11) In case of outlet pressure variation open or close the restrictor installed in the inlet of pilot.  
12) Since the pressure is stable, open the vent valve and check the set point. 
13) If the pressure is correct, close the vent valve and check lock up. 
14) Since the set point was achieved turn counter-clockwise the regulating spring of pilot of second stage pressure 

regulator to allow it regulate the pressure. 

15) Adjust  set  point  of  second  stage  pressure  regulator  at  least  0.5  kgf/cm²g  lower  than  override  (extra)  pilot  of 

first  stage  pressure  regulator  to  allow  the  regulator  remain  totally  open  and  only  the  second  stage  pressure 
regulator works. 

16) In case of outlet pressure variation open or close the restrictor installed in the inlet of pilot.  
17) Since the pressure is stable, open the vent valve and check the set point. 
18) If the pressure is correct, close the vent valve and check lock up. 
19) Turn  counter-clockwise  the  regulating  spring  of  main  pilot  of  first  stage  pressure  regulator  up  to  set  point 

desired to allow such regulator assume the regulating pressure. In this moment, the pressure regulating skid 
will reduce the pressure in two stages. 

20) Verify if there is any leak in the connectors and fittings. 
21) Open SLOW AND GRADUALLY the outlet ball valve to pressurize the skid completely. 
22) If necessary, proceed with thin pressure adjustment using pilot and restrictor installed on it. 

 
 
 
 

Summary of Contents for ARGOS

































Reviews: