background image

  

 

 

FCC Compliance Statement      

The FCC Wants You to Know: 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC rules.  These limits are designed to provide reasonable protection against harmful 
interference in a residential installation.  This equipment generates uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications.  However, there is no guarantee that interference will not occur in a particular 
installation.  If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures : 
a)  Reorient or relocate the receiving antenna. 
b)  Increase the separation between the equipment and receiver. 
c)  Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. 
d)  Consult the dealer or an experienced radio/TV technician. 

FCC Warning 

Modifications not expressly approved by the manufacturer could void the user authority to operate the 
equipment under FCC Rules. 

 

This document is the property of: 

ORPAK SYSTEMS Ltd. 

ISRAEL 

 

Summary of Contents for 800938653



























































































Reviews: