manualshive.com logo in svg

GAS GAS WILD HP 450, Service Manual, Page: 60 / 63

Share
Download
GAS GAS WILD HP 450 Service Manual Download Page 60

- Steering stem bent.
- Wheel misalignment..

- Posible knock to one of steering kneecap.

- Pad or disc worn.
- Brake fluid leak.
- Brake fluid deteriorated.

- Piston pump damaged.
- Brake maladjusted.

- Tension regulator is damaged.

- Ilumination fuse is blown.

- Change direction axis. Go to specialized garage.
- Check front wheels convergence and divergence. Centre
swing arm axle.
- Go to specialized garage.

- Check pad and replace if it is necesary.
- Check and repalce if it is necesary.
- Empty brake fluid and replace with new recomended one.
(Look how purge the fluid brake in "Maintenance and
ajustment").
- Replace piston pump. Go to specialized garage.
- Adjust brake.

- Extract seat and fuel tank and check connections, and
verify tension regulator and box fuses fuse.

- Extract seat, box fuse cover and change fuse.

Pull to one side

Brakes don't hold

Lamps are blown

Ilumination system don't operate

21

22

23

24

WILD HP -

125

-

TROUBLE

CAUSE

REMEDY

Summary of Contents for WILD HP 450
































































Reviews:

No comments