manualshive.com logo in svg

GAS GAS WILD HP 450, Service Manual, Page: 18 / 63

Share
Download
GAS GAS WILD HP 450 Service Manual Download Page 18

- Charge duration = 6 hours minimum / 24 hours maximum.

3.2.  Charge mode with constant power.
        - Maximum charge power = 0.1 Cn.

- Recommended charging time = 5 - 8 hours.
- The product of (charging power) x (charging time) has to stay within 
the range:0,5 - 0,8 Cn.

NOTE

I

n case charging modes different than the established ones are

used, by no means, may the maximum allowed power or the
charging time of 24 hours be surpassed.

FRONT GUARD

The front guard projects from the quad. In case of a front crash, the
protection, attached directly to the frame, will absorb the crash and
prevent the steering and the rest of the vehicle from suffering
significant damage.

WILD HP -

83

-

SEAT

To remove the saddle, use the same key that was used to open the
petrol-tank cap

 (B)

. Insert the key into the lock located on the right-

hand side of the QUAD. Turn the key clockwise, and then insert your
hand through the rear, between the saddle and the frame. The saddle
will lift easily.

NOTE

When putting the seat back in the normal position, make sure
it holds well back in place.

BATTERY

This battery is maintenance free and checking the fluid level is not
required. It is recommended to check the charge of the battery
periodically.
The operating instructions for the battery are as follows:

1.

Check the battery tension while the circuit is open.

2.

In case the battery’s tension is below 12.60 V, or if the storage period
has exceeded 6 months,the battery has to be recharged following the
instructions in paragraph. In case the tension is above 12.60 V, the
battery can be installed on the vehicle without having to recharge it.

3.1. Charge mode with constant tension.

- Constant tension = 14.40 - 14.70V
- Initial charging power = 0.1 - 0.5 Cn

(B)

CAUTION

Exceeding charge standards may reduce the life cycle of the battery.
Never surpass charge standards.

CAUTION

Inverting the polarity of the battery terminals may cause battery
charge problems and cause damage to it.
The red terminal is the positive (+) and the black terminal is the
negative (-).

Summary of Contents for WILD HP 450
































































Reviews:

No comments