background image

Magnum DS80F & DS80C Dual-speed Stackable Hubs        Installation and User Guide (12/01)

2

www  GarrettCom  com

.

.

Power Input Voltage: 36 to 70 VDC (auto ranging), “-, GND, +”
Power Consumption: 8 watts typical, 10 watts max.

Network Cable Connectors - 

for eight RJ-45 shielded female ports and 1 fiber port

100Mbps:  Category 5 UTP/STP, fiber (50/125, 62.5/125, 9/125 micron)

10Mbps: Category 3, 4, 5 UTP  (Note: auto-sensing does not sense cable type)

Maximum Load per port: 60 mA

Up-Link, Port # 1 SW

 Port 1SW (switched RJ-45) has a manual crossover (MDIX up-link) switch for

connection to a central switch or to another DS80F, DS80C (or equal) unit.

Manual Switch

       DS80C: “FF” or “A” switch

 Port 2SW (a switched port) has a “FF-A” manual switch. In the “FF” position, it

fixes port 2 at Full 100Mb. In the “A” position, port 2 is set at auto-negotiation

DS80F: “F” or “H” switch

Ports 

1SW and 2SW (the switched ports) have a common “F-H” manual switch.

In the “F” position, it causes full-duplex mode to be advertised for the standard

802.3u auto-negotiation session on port 1SW. For fiber, it forces full-duplex

mode at 100Mb. In the “H” position, it causes half-duplex mode to be advertised

for auto-negotiation, and for fiber it forces half-duplex mode.

 

See Section 4.3 for details.

Packaging

                       Enclosure:  Rugged high-strength sheet metal. Metal mounting clips 

included. Suitable for wiring closet shelf, wall or desktop mounting.
Dimensions: 1.25 in H x 6.75 in W x 5.0 in D (3.2 cm x 17.1 cm x 12.7 cm)
Weight (of hub unit): 1.0 lb. (455 g.)
Weight (of power supply unit): 1.0 lb. (455 g.)
Cooling method: Convection

LED Indicators

PWR:

Steady On when power applied

ERROR:  Self-test at power up failed

 

SPEED (with LINK ON): ON = 100Mbps; OFF = 10Mbps

  

LINK/ACT: Steady On for LINK with no traffic, blinking indicates port 

      is transmitting / receiving.

F/H (for port 1SW and 2SW only): ON = full-duplex, OFF = half-duplex

                Agency Approvals

UL Listed (UL 1950), cUL, CE
Emissions:  meets FCC Part 15, Class A

 Warranty:   

Three years, return to factory

        Made in USA

Summary of Contents for DS80C




























Reviews: