background image

Magnum DS80F & DS80C Dual-speed Stackable Hubs        Installation and User Guide (12/01)

6

www  GarrettCom  com

.

.

2.2.1

Magnum DS80F chassis with fiber ST or SC (mm or sgl. mode) connector

Fiber ST above, fiber SC at right

The Magnum DS80F chassis

houses one main PC board.  The power supply unit is external.  The front side of the chassis has

eight RJ-45 twisted-pair ports and one 100Mbps fiber port.  Port #2SW always supports fiber

ports only and the RJ-45 connector is inoperative at all times.  LEDs to indicate operating status

of all ports are mounted on the top.  There are power (PWR) and ERROR (self-test at power up

failed) indicators for the unit. For each port, there are Link and Activity (LINK/ACT) LEDs

indicating traffic, and speed (ON for

100Mbps). Switched ports 1SW and 2SW

have full-half (F-H) duplex indicators.

The DC power plug connector or

“jack” is in the left rear of the chassis.

 

Rear View Magnum DS80-Series

The external power supply is 5VDC at either 95 - 125vac at 60 Hz for “-d” models or 120-

250vac at 50Hz for “-i” models that have IEC power cable connector in the external power

supply housing.

2.2.2

Magnum DS80C chassis with all RJ-45 Copper ports

The Magnum DS80C chassis

houses one main PC board.  The power

supply unit is external.  The front side of the

chassis has eight RJ-45 twisted-pair ports.

The 1SW and 2SW ports are switched ports

with selectable Fullfixed- and Auto-negotiation (FF-A) capability.  See section 4.4.

LEDs to indicate operating status of all ports are mounted on the top.  There are power

(PWR) and ERROR (self-test at power up failed) indicators for the unit. For each port, there are

Link and Activity (LINK/ACT) LEDs indicating traffic, and speed (ON for 100Mbps). Switched

ports 1SW and 2SW have full/half (F/H ON for full duplex) duplex indicators.

Tx         Rx

UPLINK

F

H

=     X

2SW

UPLINK

                             3            4              5            6            7             8

1SW

Magnum DS80 Dual Speed

Personal Hub

PORTS               1SW      2SW          3           4              5            6             7            8

Speed

Link/Act

F/H

Power
Error

GARRETT

12V, 1.5Amps

Tx         Rx

UPLINK

F

H

=     X

2SW

UPLINK

                             3            4              5            6            7             8

1SW

Magnum DS80 Dual Speed

Personal Hub

PORTS               1SW      2SW          3           4              5            6             7            8

Speed

Link/Act

F/H

Power
Error

GARRETT

12V, 1.5Amps

F

H

Magnum DS80F Dual Speed

Personal Hub

PORTS               1SW      2SW          3           4              5            6             7            8

Speed

Link/Act

F/H

Power
Error

GARRETT

12V, 1.5Amps

DC 12V

Tx         Rx

UPLINK

F

H

=     X

2SW

UPLINK

                             3            4              5            6            7             8

1SW

Magnum DS80 Dual Speed

Personal Hub

PORTS               1SW      2SW          3           4              5            6             7            8

Speed

Link/Act

F/H

Power
Error

GARRETT

5VDC, 2Amps

Summary of Contents for DS80C




























Reviews: