background image

2

Plug the power cable into a power

source.
The status LED is solid red when the

collar is charging.

3

After the status LED turns solid green,

remove the charging clip from the

collar.

Turning On the Dog Collar Device

• On the dog collar device, hold the

power key until the status LED turns

green and the collar beeps to turn it

on in training mode.

• On the dog collar device, hold the

power key until the status LED turns

blue to turn on the BarkLimiter™

feature (page 9).

• On the dog collar device, hold the

power key until the status LED turns

yellow to enter pairing mode

(page 5).

Turning Off the Device

1

On the dog collar device, hold the

power key until the red LED appears.

2

Release the power key.
The dog collar device beeps to

confirm powering off.

NOTE: 

If the device is powered off in

BarkLimiter mode, the LED flashes

the number of corrected barks before

powering off (page 10).

Dog Collar Device

You can use up to 6 dog collar devices

with a single handheld device.
Each dog collar device must be paired

with the handheld device before it can be

used. During the pairing process, each

dog collar device is associated with a

different color on the handheld device.

Pairing a Dog Collar Device with the

Handheld Device

NOTE: 

If your handheld device and dog

collar device were included in the same

5

Summary of Contents for Pro 70

















Reviews: