Page 16
Part # MCOSM06 Rev 1 (11/03/08)
Setting the cook temperature, hold temperature and time
are done in the same manner. Pressing the
SET
key will
light the
TEMP
LED. The operator then sets the temperature
by rotating the dial on the controller until the desired
temperature is shown on the display. Pressing the
SET
key a
second time will light the
HOLD
LED and allows the operator
to select the desired hold temperature as shown on the
display. Pressing the
SET
key a third time lights the
TIME
LED
and allows the operator to select the desired cook time as
shown on the display. Pressing the
SET
key a fourth time ends
the programming.
Pressing the
START/CANCEL
key will start the timing cycle.
When the cycle is completed, pressing this key will also cancel
the
"DONE"
prompt. To cancel a timing cycle in progress press
and hold the
START/CANCEL
key for 3 seconds.
Core Probe Operation
The
Core Probe option
(455 Controller Only) is only active
when the core probe is plugged into its connector. To set the
core temperature, first plug the core probe into its connector.
The display will indicate
"100"
and the
CORE TEMP
LED will
be on. The operator then sets the temperature by rotating
the dial on the controller until the desired temperature is
shown on the display. Pressing the
SET
key stores the core
temperature and starts the cooking process.
To set the oven temperature, press the
SET
key again. The
TEMP
LED will light and the oven temperature can be
set by rotating the dial on the controller until the desired
temperature is displayed. Pressing the SET key again will
light the
HOLD
LED allowing the operator to set the hold
temperature in the same manner.
NOTE:
If the hold temperature is not set, the default hold
temperature is 150°F (66°C) or the last programmed
temperature. (Hold temperature range is 140°F (60°C) to
210°F (99°C).
When the core temperature is reached, the display will sound
and flash
"DONE"
for 3 seconds. Automatically, the display
will switch to count
"UP"
the time the oven is on hold.
CHANGING FACTORY SETBACK PROGRAM
To change the factory setback settings, press and hold the
SETBACK
key for two seconds. The
TEMP
LED will light and
a temperature will be displayed (factory preset at 250°F
[121°C]). Set the temperature using the dial, then press the
SET
key. The
TEMP
LED will go out and the
TIME
LED will light.
Set the time using the dial, then press the
SET
key. Press the
SET
key one more time to exit programming.
Note: To disable the setback function, set the temperature to
250º F (121ºC) and the time to zero..
Summary of Contents for Master 200
