background image

Part # 4521635 (03/04/08)

Page 3

SECTION 1 –SAFETY

Description Of Warning Signs

Identifies safety information about 

dangers which may cause serious personal 

injury if equipment is not operated 

properly.

Dangerous voltage warning symbol, 

indicates a risk of electric shock and 

hazards from dangerous voltage.

CAUTION

Indicates a hazard or unsafe practice 

which could result in minor personal 

injury or property damage.

Electromagnetic field.

Warning signs mounted directly on the cooker must be 

observed at all times and kept in a fully legible condition.

Personnel Qualification And Training

All persons involved in assembly, installation, commissioning, 

operation and maintenance must have the appropriate 

qualifications. The scope of responsibility, competence and 

supervision of the staff must be defined and controlled. 

Safety Information, Installation And Service

Operators of the equipment must ensure that all installation, 

service and as well as all inspections, are performed by 

authorized and qualified personnel. Before attempting to 

operate the equipment carefully read the information and 

instructions outlined in the ”Installations and Operating” 

manual. For all installations, service, maintenance, repair 

and or overhaul of the induction cookers, personnel must 

be specially qualified and must have attended a technical 

training course authorized by Garland.

Do not attempt to perform any repairs or replace any part of 

the induction cooker unless, all power supply to the cooker 

has been disconnected.

Unauthorized Reconstruction And  

Use Of Spare Parts

Reconstruction of the cooker or changes to the cooker are 

not allowed. Contact the manufacturer if you intend to do 

any changes to the cooker. To guarantee safety, use only 

genuine OEM spare parts and accessories, authorized by the 

manufacturer. Garland will not be held liable for any damage 

or injury caused by used of other components.

Improper Operating Methods

The operating reliability of the cookers can only be 

guaranteed when the cooker is used appropriately. The limit 

values stated in this manual must not be exceeded.

Summary of Contents for Enodis GIU-1.5 (BH/BA 1500)

























Reviews: