Part # 1955203 (12/06)
Page 11
Cook-N-Hold Operation
Pressing the
COOK/HOLD
( and Controllers
Only) key activates the Cook-N-Hold mode and lights
is LED. To verify the proper hold temperature has been
selected, press the
SET
key twice. The display will show
the hold temperature. At the end of the cook cycle, an
audible alarm will sound, the display will flash “
DONE
”
and change to count “
UP
” the time the oven is on
hold. The oven will switch to the programmed hold
temperature.
Setting the cook temperature, hold temperature and
time are done in the same manner. Pressing the
SET
key will light the
TEMP
LED. The operator then sets
the temperature by rotating the dial on the controller
until the desired temperature is shown on the display.
Pressing the
SET
key a second time will light the
HOLD
LED and allows the operator to select the desired hold
temperature as shown on the display. Pressing the
SET
key a third time lights the
TIME
LED and allows the
operator to select the desired cook time as shown on
the display. Pressing the
SET
key a fourth time ends
the programming.
Pressing the
START/CANCEL
key will start the timing
cycle. When the cycle is completed, pressing the key will
also cancel the “
DONE
” prompt. To cancel a timing
cycle in progress press and hold the
START/CANCEL
key for seconds.
Core Probe Operation
The
Core Probe option
( Controller Only) is only
active when the core probe is plugged into its connector.
To set the core temperature, first plug the core probe into
its connector. The display will indicate “” and the
CORE TEMP
LED will be on. The operator then sets
the temperature by rotating the dial on the controller
until the desired temperature is shown on the display.
Pressing the
SET
key stores the core temperature and
starts the cooking process.
will indicate “
DOOR
”.
This is a patented safety feature.
Pressing the
COOL DOWN
key again will turn the
LED off and stop this mode. Pressing the
ON/OFF
key
will also cancel Cool down. Cool Down is not active
during a cook.
When the
ON/OFF
switch is pressed to turn the oven
off and the oven was above °F (°C), the oven will
go into an
AUTO COOL DOWN
mode. In Auto
cool Down, the oven will run the fan on high until
the oven cavity drops below °F (°C). During this
time the display will indicate “
AUTO
”. When the oven
temperature drops below °F (°C) the oven turns
off.
This feature protects the oven motor from premature
failure.
Optimal cool-down will be achieved with door
open slightly.
Fahrenheit/Celsius
Factory default is Fahrenheit (F). To change to
Celsius (C), press and hold in the “Phantom Key” located
to the right of “Cook/Hold” key. “F” appears in the
display. Continue to hold until “C” is displayed and
then release the “Phantom key”
Operating the Controls
Setting the cook temperature and time are done in the
same manner. Pressing the
SET
key will light the
TEMP
LED. The operator then sets the temperature by rotating
the dial on the controller until the desired temperature is
shown on the display. Pressing the
SET
key a second time
lights the
TIME
LED and allows the operator to select
the desired cook time as shown on the display. Pressing
the
SET
key a third time ends the programming.
Pressing the
START/CANCEL
key will start the timing
cycle. The display will count down from the Set time in
minutes and seconds (solid colon) or hours and minutes
(blinking colon) then minutes and seconds. When the
cycle is completed, pressing this key will also cancel
the “
DONE
” prompt. To cancel a timing cycle in
progress, press and hold the
START/CANCE
L key for
seconds.
OPERATING INSTRUCTIONS Continued
Summary of Contents for Convection Microwave Oven
Page 2: ...Part 1955203 12 06 Page 2...
Page 21: ......
Page 22: ......
Page 43: ...Pi ce n 1955203 12 06 Page 2...