Gared Sports PSS FGP400 Series Installation And Maintenance Instructions Manual Download Page 3

  

FGP Series Football Goal Posts   

 

 

Introduction/Liability Disclaimers

 

Thank you for your purchase of a Gared Sports FGP Series Football Goal Post.  To ensure that 
our equipment will provide years of use to you, we are including this installation and 
maintenance guide.  This guide will provide information on the proper assembly and installation 
methods and preventative maintenance of your football goal post. 
 
Please note that a Bill of Materials is being included with this guide.  Please check that all of the 
parts called out on the Bill of Materials are present prior to beginning assembly.  Please do not 
substitute for factory parts.  Please contact the Gared Sports customer service department and 
allow them to determine if substitute parts are acceptable. 
 
It is recommended that an individual who has been properly trained perform assembly and set up 
of the Football Goal Post.  No one under the age of 18 should attempt assembly or set up of the 
unit, unless properly supervised. 
 
To prevent normal wear and tear from shortening the life of the unit, preventative maintenance 
inspections and repairs should be performed at least once per year.  If the units are subject to 
high or unusual usage, inspections should be scheduled to occur more frequently.  If items are 
found to be nonconforming, replacements can be ordered from Gared Sports or one of our 
authorized dealers.  When contacting Gared Sports, please have information regarding the 
dealer/installer who sold the unit, the name of the project, and any applicable warranty 
information. 
 
 
 

!

    WARNING 

 

 

Before proceeding with assembly, read all instructions and assembly procedures.  Make 
sure all parts have been received and are not damaged. 

Do  not  allow  persons  to  hang  on  Football  Goal  Post.    Serious 
injury  may  occur  from  a  fall.    All  football  goal  posts  must  be 
installed  properly  to  avoid  injury  from  tip  over.    Read  and 
understand all assembly instructions. 

Summary of Contents for PSS FGP400 Series

















Reviews: