![background image](http://html1.mh-extra.com/html/gardner-denver/apex25-30a/apex25-30a_operating-and-service-manual_3576437018.webp)
13-25-608 Page 17
When piping two or more rotary screw units on a common discharge line, each unit shall be isolated by
the check valve in the unit discharge line.
If a rotary screw and a reciprocating compressor are piped to a common discharge line, an air receiver
must be located between the two units.
Discharge air used for breathing will cause severe injury or death.
Consult filtration specialists for additional filtration and treatment equipment to
meet health and safety standards.
ELECTRICAL WIRING - Standard Units -
The compressor package is factory wired for all connections
from the starter to the motor, for the horsepower and voltage specified on the order. The standard unit is
supplied with:
·
UL Type 4 (NEMA 4) starter and controls enclosure and TEFC main motor on FS variants. Note that
the overload settings are to be selected based on motor nameplate full load amperage
·
UL Type 1 (IP54 VFD and controls enclosure and TEAO main motor on VS variants.
See
“Location” paragraph on page 13, for distance to the nearest obstruction on the control box side of
the package.
Perform all wiring in accordance with the National Electrical Code (NFPA-70) and any applicable local
electrical codes. Wiring must be performed only by qualified electricians.
Electrical shock can cause injury or death. Open main disconnect switch,
lockout and tag out before working on control box.
Electrical Wire Sizing -
A certified electrician familiar with National Electric Codes and applicable local
codes shall size the electrical power wires serving the compressor package. Refer to Figure 2-4, 2-5 for a
summary of maximum package current draw values.
Power
Phase-Voltage Max Current Draw - amps
25 / 30 HP package
3-575
30.1 / 35.4
"
3-460
37.6 / 43.8
"
3-230
73.6 / 86.1
"
3-208
82.9 / 94.9
RNC 125 dryer
1-115
18.0
RNC 150 dryer
1-115
18.0
Figure 2-4 – Electrical Wiring Sizing – FS Variants
Summary of Contents for APEX25-30A
