![background image](http://html1.mh-extra.com/html/gardner-denver/apex25-30a/apex25-30a_operating-and-service-manual_3576437054.webp)
13-25-608 Page 53
All materials used in Gardner Denver compressor units are compatible with
AEON 9000SP Lubricant. Use caution when selecting downstream components
such as air line lubricating bowls, gaskets and valve trim.
AEON 9000SP Synthetic Lubricant is not compatible with low nitrile Buna N or
acrylic paints. AEON 9000SP is compatible with most air system downstream
components.
Material Safety Sheets (MSDS) are available for all AEON lubricants at web address.
www.gardnerdenverproducts.com/downloads.aspx
LUBRICANT CHANGE PROCEDURE
- If upgrading to a different lubricant type (e.g., longer life, higher
temperature, food grade, etc.), following the proceeding steps.
1. Be sure the unit is completely off and that no air pressure is in the oil reservoir.
2. Disconnect, tag and lockout the power supply to the starter.
3. Thoroughly drain oil system while hot
– refer to Compressor Illustration on Page 52 for location of
various drain points:
·
Drain oil from oil sump by opening the drain valve at its bottom. Close drain valve.
·
Drain oil from the air end by removing the G1-1/2
” plug at the bottom of the discharge housing.
Replace the plug.
·
Drain oil from the oil cooler by removing the G3/4
” plug on the oil header. Replace the plug.
·
Remove and drain oil from the oil filter. Reinstall the used filter.
4. Fill the system with a 50 percent charge of the new lubricant:
·
Start the machine and monitor its operation.
·
Allow the machine to reach a stable discharge temperature (5-7min), then shut down.
5. Thoroughly drain oil system
– see Item 3 above.
6. Replace used oil filter and air/oil separator element with new ones.
7. Fill the system with a full charge of the new lubricant.
8. Machine should then be run normally; however, total run time after the initial change-out should be 50
percent of normal anticipated service life of the new lubricant.
·
Drain all lubricant from the system, change the filter and separator, and replace with a full charge
of the new lubricant.
7. Subsequent lubricant change-outs should be at normal intervals. (See
“Oil Change Interval”, Figure
5-4, page 58)
COLD AMBIENT OPERATION
- See
“Installation for Cold Weather Operation”, page 164 and Figure 2-3,
page 15.
Summary of Contents for APEX25-30A
