13-18-603 Page 102
SECTION 9
MINIMUM PRESSURE/CHECK VALVE
MINIMUM PRESSURE/CHECK VALVE
- This device maintains minimum pressure within the air/oil
reservoir, thus insuring (cooling/lubricating) oil injection flow into the compressors. It also serves as a
check valve to prevent back flow of compressed air flow from the customer
’s piping or pipe network back
into the compressor package when the compressor is not active. The valve does not require
maintenance or adjustment. If the valve fails to function, check the valve stem O-ring for sealing, valve
orifices for restriction, or valve and valve seat for burrs and dirt. Repair kits are available from your local
authorized Gardner Denver distributor.
Before servicing the minimum pressure valve, always stop the unit, release air
pressure, lockout and tagout the power supply to the compressor package.
Failure to release pressure or properly disconnect the power may result in
personal injury or death.
NOTICE
Working spring within valve body is under tension. Failure to relieve spring
tension gradually may cause serious injury upon cap removal.
Minimum Pressure/Check Valve (MPV) Inspection:
(See Figure 9-1)
1. Be sure the unit is completely off and that the oil sump is depressurized
– including pipe works
between MVP and (external) isolation valve.
2. Disconnect, lockout and tagout power supply to the compressor package.
3. Tighten nut (13) on the MPV cover (16).
4. Unscrew bolts fastening MPV housing (1) to the sump housing and remove MPV.
5. Remove snap ring (9).
6. Remove internal assembly (2-20) away from MPV housing (1) and inspect or replace components.
7. Re-assemble internal assembly (2-20) into MPV housing (1) in reverse order.
8. Clean o-ring sealing surfaces between sump and bottom of MPV housing (1). Inspect, clean and or
replace o-ring prior to re-installation.
9. Re-install MPV unto sump with provided bolts.
10. Adjust nut (13) so that there is a small (.08
”) between itself and the cover (16).
11. Check for leaks after unit is back in operation.
Summary of Contents for AirSmart VS25A
