background image

 10 

1.

 

Display:  

a.

 

The screen will display actual relative humidity (%) and ambient 
temperature 

(℃

) when the machine is off.   

b.

 

The screen will display following message when the machine is on.   
1. Mode;   2. Actual relative humidity(%)    and ambient temperature

(℃

);   

3.Fan speed and timer if set.   
 

2.

 

Setting: 

a.

 

Mode setting 

When the machine is on, press M key to switch the mode: 

Dehumidifying mode: 

 

Ventilation mode: 

 

Heating mode: 

    ( only available with extra heating element ) 

Dehumidifying and Heating: 

   

b.

 

Set Humidity (setting range: 30%—99%)   

In the dehumidifying mode 

  no matter machine’s on or off, every time 

you press button “

” or

“▼”

, the set humidity will be increased or 

decreased by 1%. It’ll flash for 8 seconds and then display the actual 
humidity again.   
 
To check the set humidity, press 

 or 

  key under dehumidifying mode.. 

 

c.

 

Set Fan Speed: 

When the machine

s on and in ventilation mode 

, press 

SET

 to 

switch the speed from High speed 

and low speed

”.  

 

Summary of Contents for FAI-150-0151






























Reviews: