Gantner GAT ECO.Side Lock 7010 F/ISO Installation, Configuration & Operation Download Page 7

Page: 7 / 64

GAT ECO.Side Lock 7010 (NW) F/ISO
Table of Contents

www.gantner.com

HB_GAT-ECOSide-Lock7010-FISO--EN_11

TABLE OF CONTENTS

INTRODUCTION .......................................................................................... 9

About this Manual ..................................................................................................................................... 9

1.2

Chapter Overview ..................................................................................................................................... 9

1.3

Contact & Inquiries ................................................................................................................................... 9

1.4

Target Groups ......................................................................................................................................... 10

1.5

Formatting ............................................................................................................................................... 10

1.5.1

Safety-Critical Information .................................................................................................................... 10

1.5.2

Non-Safety-Critical Information ............................................................................................................ 10

1.5.3

Instructions and Results ....................................................................................................................... 10

GENERAL INFORMATION ........................................................................ 11

2.1

Intended Use........................................................................................................................................... 11

2.2

Functional Description ............................................................................................................................ 11

2.3

Terminology ............................................................................................................................................ 12

2.4

RFID Technology .................................................................................................................................... 13

2.5

System Components .............................................................................................................................. 14

INSTALLATION ......................................................................................... 17

3.1

Target Group........................................................................................................................................... 17

3.2

Definition of the Door Hinge (Right of Left Door) .................................................................................... 17

3.3

Test Installation ....................................................................................................................................... 18

3.4

Metallic and Non-Metallic Doors ............................................................................................................. 18

3.5

Bolt Gauge .............................................................................................................................................. 18

3.6

Door Status Contact ............................................................................................................................... 19

3.7

Transportation Guidelines ....................................................................................................................... 19

3.8

Replacement after a Burglary Attempt ................................................................................................... 19

3.9

Measurement Diagrams for Installation .................................................................................................. 20

3.9.1

Door Width ........................................................................................................................................... 20

3.9.2

Dimensions of the GAT ECO.Side Lock 7010 F/ISO and GAT NET.Lock Bolt Sets ........................... 20

3.10

Installation in Lockers with Non-Metallic Doors (except glass) .............................................................. 22

3.10.1

Installation Requirements for the GAT ECO.Side Lock 7010 F/ISO and Bolt Set ............................... 23

3.10.2

Installation Instructions for the GAT ECO.Side Lock 7010 F/ISO and Non-Metallic Doors ................. 24

3.11

Installation in Lockers with Metallic Doors .............................................................................................. 25

3.11.1

Cutouts in the Locker Door .................................................................................................................. 26

3.11.2

Installation Requirements for the GAT ECO.Side Lock 7010 F/ISO and Bolt Set ............................... 27

3.11.3

Installation Instructions for the GAT ECO.Side Lock 7010 F/ISO and Metallic Doors ......................... 28

3.12

Installation in Lockers with Glass Doors ................................................................................................. 29

3.12.1

Installation Requirements for the GAT ECO.Side Lock 7010 F/ISO and Bolt Set ............................... 30

3.12.2

Installation Instructions for the GAT ECO.Side Lock 7010 F/ISO and Glass Doors ............................ 31

COMMISSIONING ..................................................................................... 33

4.1

Target Group........................................................................................................................................... 33

4.2

Power Supply .......................................................................................................................................... 33

4.2.1

Battery Information ............................................................................................................................... 33

4.2.2

Inserting the Battery ............................................................................................................................. 33

4.2.3

Replacing the Battery ........................................................................................................................... 34

4.3

USB Connection ..................................................................................................................................... 35

4.4

Automatic Antenna Adjustment .............................................................................................................. 37

4.4.1

Antenna Adjustment using the SERVICE Data Carrier ....................................................................... 37

4.4.2

Antenna Adjustment via GAT Config Manager .................................................................................... 37

Summary of Contents for GAT ECO.Side Lock 7010 F/ISO

































































Search results

Summary of Contents for GAT ECO.Side Lock 7010 F/ISO

Reviews:

Related manuals for GAT ECO.Side Lock 7010 F/ISO

Brands by name

Popular brands

Gantner GAT ECO.Side Lock 7010 F/ISO, Installation, Configuration & Operation

Search results

Summary of Contents for GAT ECO.Side Lock 7010 F/ISO

Reviews:

Related manuals for GAT ECO.Side Lock 7010 F/ISO

Brands by name

Popular brands