background image

1

LIMITED WARRANTY

GAMMA Sports (GAMMA) warrants to the original purchaser that the X-STRINGER stringing machine ("EQUIPMENT")
purchased is free from defects in materials and workmanship for a period of five (5) years from the date of original purchase
for mechanical parts (excluding any electrical parts and string clamps), and for a period of one (1) year from the date of
purchase for any electrical parts and string clamps. Should any defects develop under normal use within the specified time
periods, GAMMA will at its option, repair or replace the defective EQUIPMENT provided it is returned to GAMMA prepaid at
the purchaser's expense. This warranty does not apply to any damage or defect caused by negligence, abuse, misuse,
unauthorized alteration, shipping, handling, or part wear and tear as a result of normal use.

Routine maintenance, adjustment, and cleaning required to ensure proper operation are the responsibility of the purchaser
and are not covered under the terms of this warranty.  These include, but are not limited to:  String Clamp adjustment, as
described on page 13, tension calibration, as described on page 11, Tensioner Brake adjustment, as described on page 12,
and clamp base locking nut adjustment, as described on page 13..

GAMMA's obligation under this warranty is limited to repair or replacement of defective EQUIPMENT, and no one is authorized
to promise any other liability. GAMMA shall in no event be liable for any incidental or consequential damages.

To return defective EQUIPMENT, a return authorization (RA#) must be obtained from a GAMMA customer service
representative. The RA# must be marked on the outside of the shipping carton being returned. All returns must be shipped
prepaid by the customer to GAMMA. Please retain the original shipping carton and packing materials for any future shipments.
GAMMA will not be responsible for machines which are not sent in the original undamaged packaging.

TABLE OF CONTENTS

PAGE 1 ................................................................................................ WARRANTY

PAGE 2 ................................................................................................. FEATURES

PAGE 3 ..................................................................... ASSEMBLY INSTRUCTIONS

PAGE 6 ........................................................................... MOUNTING THE FRAME

PAGE 7 .......................................................................... STRINGING THE FRAME

PAGE 10 ........................................................................ ADDITIONAL FEATURES

PAGE 11 .................................................................................. PATHFINDER AWL

PAGE 12 ................................................... MAINTENANCE AND ADJUSTMENTS

PAGE 15 ..................................................................... TROUBLESHOOTING TIPS

PAGE 17 .............................................................................................. PARTS LIST

PAGE 18 .................................................................................... PARTS DRAWING

OWNER'S MANUAL

GAMMA X-ST

Summary of Contents for X-Stringer




















Reviews: