all copying, even par tial, of this manual is strictly forbidden
FC66003632 - Rev 00
29
ESTRO BLDC
10 ACCESSORIES
MYCOMFORT LARGE - Wall-mounted microprocessor
control, GALLETTI model MYCOMFORT LARGE
having
the following main features:
- room air temperature reading and adjustment
- room humidity reading and adjustment
- water temperature reading (water sensor as an
optional)
- manual and automatic adjustment of fan speed
- manual and automatic switching of heating
and cooling mode depending on the water
temperature within the heat exchanger or on the room temperature,
with a neutral zone that can be selected in the range from 2° to 5°C
- clock and hourly timer-programmed operation
- 2 analogue outputs for controlling modulating devices 0-10V
- 2 digital outputs for controlling (On/Off) external devices (no-voltage
contacts)
- serial port for Bus connection
The controller is equipped with a large display (3”) to show and set all the
functions of the unit.
Using the installation kit available, myComfort can be mounted on the unit.
ZA - pair of support covering feet for FAI models
The ZA covering feet, designed for the installation
on éstro FAI models are supplied in pairs and
comprise supports for fastening to the base
unit and outer coverings for fastening to the
cabinet. They are used to conceal the plumbing
(pipes leading up from the floor) and in cases
where the fan coil unit cannot be anchored to
the wall. The height of covering feet is 100 mm.
ZAG - pair of support covering feet with front
grille for FA models
The ZAG covering feet, designed for the
installation on éstro FAI models are supplied
in pairs and comprise supports for fastening to
the base unit, outer coverings for fastening to
the cabinet and the front covering grille. They
are used to conceal the plumbing (pipes leading
up from the floor) and in cases where the fan
coil unit cannot be anchored to the wall. The
height of covering feet is 100 mm.
ZL - pair of support covering feet for FLI
models
The ZL covering feet, designed for the installation
on éstro FLI models are supplied in pairs and
comprise supports for fastening to the base unit
and outer coverings for fastening to the cabinet.
They are used to conceal the plumbing (pipes
leading up from the floor) and in cases where
the fan coil unit cannot be anchored to the
wall. The height of covering feet is 100 mm.
ZLG - pair of support covering feet with front
grille for FLI models
The ZLG, ZCG covering feet, designed for the
installation on éstro FLI models are supplied
in pairs and comprise supports for fastening
to the base unit, outer coverings for fastening
to the cabinet and the front covering grille.
They are used to conceal the plumbing (pipes
leading up from the floor) and in cases where the fan coil unit cannot be
anchored to the wall. The height of covering feet is 100 mm.
D - Support brackets for FCI vertical installation
models
The D support brackets are supplied in pairs and
combined to the recess wall mounted éstro fan
coils FCI in cases where the fan coil unit cannot
be anchored to the wall.
The height of the support brackets is 100 mm.
KBESTE KIT for on-board installation on ESTRO BLDC (1 air probe +
b on-board LCD controller frame + wiring kit)
-
The LCD controller can be installed directly (on both sides) on ESTRO
BLDC units using the controller kit provided, which contains:
-
Remote air temperature probe (cable length 1.5 m)
-
LCD frame (to be added or replaced in case of flap)
-
Support for installation on the indoor unit
-
Frame
-
Sensor holder trap and clamp
pvA - painted rear covering panel for FAI
models
This panel is suitable for wall mounted FAI fan
coils with apparent rear part. For instance:
installation against glass walls. The kit includes
an upper rear covering panel and a lower rear
covering panel. The fan coils using a PVA rear
covering panel cannot be wall mounted.
pvL - painted rear covering panel for FLI and
FUI models
This panel is suitable for wall mounted FAI, FUI
fan coils with apparent rear part. For instance:
installation against glass walls. The kit includes
an upper rear covering panel and a lower rear
covering panel. The fan coils using a PVL rear
covering panel cannot be wall mounted.
