manualshive.com logo in svg

Gainscha GA-2408T Series, User Manual, Page: 52 / 93

Share
Download
Gainscha GA-2408T Series User Manual Download Page 52

50

5.14 Printer Utility – Printer Function

This function can set the functions of the printer. Please refer to following figure

5.16:

5.16

Factory Default: Click the button to restore the printer to factory Settings.

Print Test Page: Click the button to print test page for printer.

RTC Setup: Click this button to calibrate the time in the printer.

Cutter Forward Test: After clicking this button, the printer cutter can be tangent

(full cut) test.

Cutter Backward Test: After clicking this button, the printer cutter can be back

cutting (half cutting) test.

AUTO.BAS Exist Check: The AUTO.BAS file in the printer memory can be queried.

Enable Mass Storage: Enables the printer memory. After this function is enabled,

the printer cannot print. To print, restart the printer.

Format Disk: Formats the selected printer memory.

Get Info.: Get information about the printer.

Enable Buzzer: Enable the built-in buzzer of the printer

Disable Buzzer: Turn off the built-in buzzer of the printer

Summary of Contents for GA-2408T Series






























































































Reviews:

No comments