Gaggenau VI 422 10, Instruction Manual

Page: 29 / 36

28
en
Cookware test
Establishing a direct connection
Make sure that the extractor hood is switched on and is
in search mode. Search mode means that the
connection process on the extractor hood has been
started.
Refer to your extractor hood's user manual for more
information.
1 Open the Home Connect settings menu.
~
"Opening or closing the Home Connect
settings menu" on page 22
2 Turn the control knob clockwise to position 2 .
After around 5 seconds, the illuminated ring around
the control knob flashes blue and yellow alternately.
••’
is displayed on the control panel. The hob is
connected to the extractor hood once the
illuminated ring on the control knob permanently
lights up green.
3 Close the Home Connect settings menu.
~
"Opening or closing the Home Connect
settings menu" on page 22
The illuminated ring on the control knob goes out.
Direct connection unsuccessful
If, after around 30 seconds, a connection could not be
established, the illuminated ring around the control
knob lights up red. Turn the control knob to another
position and then back to position
2 .
The illuminated ring on the control knob lights up blue.
After around 5
seconds, the illuminated ring around the
control knob flashes blue and yellow. The appliance is
trying to establish a connection again.
Connecting another hob to the extractor hood
In order to connect another hob to the extractor hood,
run through the direct connection again with the second
hob.
Controlling the extractor hood via the
hob
In the Home Connect app, you can adjust the behaviour
of your extractor hood depending on whether the hob or
individual cooking zones are switched on or off.
t
Cookware test
Cookware test
This function can be used to check the speed and
quality of the cooking process depending on the
cookware.
The result is a reference value and depends on the
properties of the cookware and the hotplate being used.
1 Fill the pan with approximately 200 ml water and
place it at room temperature in the middle of the
hotplate that most closely matches the diameter of
the pan base.
2 Go to the basic settings and select the
™„
setting.
‹””
will be lit.
3 Touch the
@
or
A
symbol.
‹¯
will be lit. A signal
tone will sound and the hotplate indicators will be
lit.
The function has now been activated.
¥—¯
will be lit. After a few seconds, the hotplate
displays will show the results for the quality and speed
of the cooking process.
Check the result using the following table:
To activate the function again, select the
@
or
A
symbol.
Result
‹
The cookware is not suitable for the hotplate and will
therefore not heat up.*
‚
The cookware is taking longer to heat up than expected
and the cooking process is not going as well as it
should.*
ƒ
The cookware is heating up correctly and the cooking
process is going well.
* If there is a smaller hotplate available, test the cookware
again on the smaller hotplate.
29
Cleaning
en
Notes
–
Do not use the wok or wok accessories with this
function.
– The Flex cooking zone is set to function as a single
hotplate; only test one item of cookware at a time on
it.
– If the diameter of the hotplate that is used is much
smaller than the diameter of the cookware, only the
middle of the cookware can be expected to heat up.
This may result in the cooking results not being as
good as expected or being less than satisfactory.
– You can find information on this function in the
section entitled
~
"Basic settings" .
– You can find information on the type, size and
positioning of the cookware in the sections entitled
~
"Induction cooking" and
~
"Flexible cooking
zone" .
D
Cleaning
Cleaning
Suitable maintenance and cleaning products can be
purchased from the after-sales service or in our e-Shop.
Hob
Cleaning
Always clean the hob after cooking. This will prevent
food deposits from becoming burned on. Only clean the
hob after the residual heat indicator has gone out.
Clean the hob with a damp dish cloth and dry it with a
cloth or towel to prevent limescale build-up.
Only use cleaning agents that are suitable for this type
of hob. Observe the manufacturer's instructions on the
product packaging.
Never use:
▯
Undiluted washing-up liquid
▯
Cleaning agents designed for dishwashers
▯
Abrasive cleaners
▯
Harsh cleaning agents, such as oven spray and
limescale remover
▯
Scouring pads
▯
High-pressure cleaners or steam jet cleaners
Stubborn dirt is best removed with a glass scraper,
available from retailers. Observe the manufacturer's
instructions.
You can obtain a suitable glass scraper from customer
services or through our online shop.
Using a special sponge for cleaning glass-ceramic hobs
achieves a great cleaning result.
Note: Do not use any cleaning agents while the hob is
still hot. This may mark the surface. Make sure that any
residue left by cleaning agents is removed.
Potential marks
Limescale and
water marks
Clean the hob as soon as it has cooled
down. You can use a cleaning agent suit-
able for glass-ceramic hobs.*
Sugar, rice starch
or plastic Clean immediately. Use a glass scraper.
Caution: Risk of burns.*
* Then clean with a damp dish cloth and dry with a cloth or
towel.