background image

10

 

REV 6/22

 

 

GB745SH

-

12 INSTALLATION TOOL S/N: 1006 AND ABOVE 

 

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

 

 

DAILY MAINTENANCE

 

 

 

WARNING

:  

Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or 

 

 wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures.

 

 

WARNING

:  

Excessive contact with hydraulic oil and lubricants must be avoided. 

 

 

WARNING:

  

Maintenance personnel 

MUST

 

read and understand all warnings and cautions.

 

 

WARNING

:

  

Disconnect tool from its power source before performing maintenance, cleaning or when replacing worn or 

 

  damaged components. Severe personal injury may occur if power source is not disconnected. 

 

 

WARNING:  

Read material Safety Data Sheet documents for all applicable materials

 

Image may not 

reflect actual tool

 

Note: 

 

• 

Dispose of hydraulic oil in accordance with manufacture safety datasheet.

 

• 

All tool materials are recyclable except rubber o

rings, seals and wipers.

 

 

The performance of any tool depends upon good maintenance practices. Following these minimal requirements daily will extend the 

life of your tool.

 

 

  *Only use a clean dry air supply set at 90

-

100 p.s.i. (6.2

-

6.9 bar) Max. equipped with a filter

-

regulator to prevent wear.

 

 

 

* Check tool and nose assembly for damage. (Replace/Repair if necessary). See overhaul (pgs.17

-

21) for tool repair.

 

 

  * Inspect hoses and couplings for wear, damage and leaks. (Replace/Repair if necessary). (See hydraulic thread preparation below).

 

 

* Verify that hydraulic hose fittings and couplings, air and electrical connections are secure. Tighten, Replace or Repair if necessary.

 

 

  * Cycle the tool several times to assure there are no leaks during use. (See hydraulic thread preparation below).

 

 

  * Keep hydraulic system free of dirt. 

 

 

  * Proper care by operators is necessary in maintaining full productivity and reducing downtime.

 

 

  

* Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with light    

 

    machine oil on a daily basis.

 

 

* All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at the end of each 

working shift to check that they are secure.

 

 

  * For a complete overhaul, service tool kit (GB745SHTK) is recommended (see overhaul pgs. 17

-

21).

 

WEEKLY MAINTENANCE

 

 

• 

Keep the hydraulic system full (only use Dexron® III or equivalent) and free of air by using the air bleeder assembly (704153) on a weekly 
basis or as needed. (See Filling and Bleeding procedure pgs. 11

-

12).

 

 
 

SEE TROUBLESHOOTING (PG. 16) AND OVERHAUL (PGS. 17

-

21) FOR FURTHER GUIDANCE.

 

TORQUE SPECIFICATIONS

 

Socket Head Cap Screws (400061) = 40 inch lbs. (4.52 Nm).

 

Button Head Cap Screws (A

-

928) = 40 inch lbs. (4.52 Nm).

 

Packing Plug (744118) = 45 foot lbs. (61 Nm).

 

Flexlock Nut (400559) = 40 inch lbs. (4.52 Nm).

 

End Cap (745616) = 45 foot lbs. (61 Nm).

 

Button Head Cap Screw (402482) = 35 to 40 inch lbs. (3.95 

-

 4.52 Nm) 

(DO NOT OVERTIGHTEN).

 

CLEANING AND LUBRICATING PROCEDURE

 

 

LUBRICATING 

 

 

Lubricate nose assembly after each cleaning

 

and as often as needed.

 

 

1.

 

 Disconnect tool vacuum line (if equipped).

 

 

2.  Point nose assembly into oil as shown.

 

 

3.  Cycle tool 8

-

10 times and wipe dry.

 

Daily cleaning and lubrication of nose assembly will greatly reduce downtime and increase life of components. Using sewing machine 

oil, or an equivalent cleaner/lubricant, follow instructions below.

 

HYDRAULIC THREAD PREPARATION

 

 

IMPORTANT:

 

Be sure to use thread sealant on all hydraulic fittings, Loctite® 545 or equivalent or a non

-

hardening Teflon® 

thread compound such as Slic

-

tite®. Tighten until fitting feels snug and then continue to tighten 1/2 to 1 full turn. 

CAUTION:

 Over 

tightening can easily distort the threads. DO NOT USE TEFLON® TAPE.

 

CAUTION:

 

Teflon® tape is an excellent thread sealer, however, 

if it is not properly applied, pieces of Teflon® may enter the hydraulic system and cause a malfunction or damage. 

 

CLEANING 

 

 

Clean nose assembly daily or as often as needed.

 

 

1.

 

Dip into mineral spirits or similar solvent to clean jaws 

and wash away metal chips and debris. DO NOT allow 

jaws to come in contact with other solvents. DO NOT let 

jaws soak. Dry jaws immediately.

 

 

2. 

 

Disassemble nose assembly and use a sharp 

pick

 

   

to remove embedded particles from grooves of jaws.

 

Summary of Contents for GB745SH-12

































Reviews: