![background image](http://html.mh-extra.com/html/gage-bilt/gb703srvt-6n10e/gb703srvt-6n10e_user-manual_555856006.webp)
8/14
6
DESCRIPTION
WARNING
:
The balance of this tool is designed for horizontal use and is not suited for any other applications.
Gage Bilt will be pleased to advise for your specific application.
The GB703SRVT/6N10E is a pneumatic-hydraulic split handle riveter designed specifically for the efficient installation of a wide range
of blind rivets. This tool’s unique "split" system provides the operator with a lightweight ergonomic tool. The head assembly when
held in hand weighs just 1.5 lbs (.68kg)! The entire split handle riveter weighs 11 lbs. (4.99 kg). It has a .780” (19.81mm) rivet setting
stroke.
The GB703SRVT/6N10E split handle riveter operates with 90 to 100 psi (6.2-6.9 bar) providing maximum efficiency. At 90 psi, (6.2 bar)
the GB703SRVT/6N10E does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles per minute.
The GB703SRVT/6N10E comes with 3 feet of hose.
The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting.
THE GB703SRVT/6N10E IS SOLD RIVET SPECIFIC. PLEASE CONTACT GAGE BILT FOR ALL OTHER APPLICATIONS.
Daily cleaning and lubrication of nose assembly will greatly reduce
downtime and increase life of components. Using sewing machine
oil, or an equivalent cleaner/lubricant, follow instructions below.
1. Disconnect tool vacuum line (if equipped).
2. Point nose assembly into oil as shown.
3. Cycle tool 8-10 times and wipe dry.
CLEANING AND LUBRICATING PROCEDURE
TORQUE SPECIFICATIONS
Socket Head Cap Screws (400061 and 400066) = 40 inch lbs.
Button Head Cap Screws (A-928) = 40 inch lbs.
Flexlock Nut (400559) = 40 inch lbs.
Packing Plug (704118) = 45 foot lbs.
End Cap (703114) = 45 foot lbs.
Button Head Cap Screws (402482) = 35-40 inch lbs.
(Do NOT over-tighten)
HYDRAULIC THREAD PREPARATION
IMPORTANT:
Be sure to use thread sealant on all hydraulic fittings, Loctite® 30534 or similar Teflon® infused pipe dope is
recommended.
CAUTION:
Teflon tape is an excellent thread sealer, however, if it is not properly applied,
pieces of Teflon may enter the hydraulic system and cause malfunction or damage. Use 1 1/2 wraps of tape
on each thread. Cut off all loose tape ends. Tighten until fitting feels snug and then go 1/2 to a full turn past
that point.
CAUTION:
Over tightening can easily distort the threads.
Image may not
reflect actual tool
MAINTENANCE
WARNING:
Maintenance personnel
MUST
read and understand all warnings and cautions.
WARNING
:
Disconnect tool from its power source before performing maintenance.
WARNING
:
Excessive contact with hydraulic oil and lubricants should be avoided.
WARNING:
Dispose of Hydraulic Oil in accordance with applicable regulations.
WARNING:
Read MSDS documents for all applicable materials.
The performance of any tool depends upon good maintenance practices. Following these minimal requirements for
service and care will extend the life of your tool.
*Only use an air supply set at 90-100 psi (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.
*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full (only use Dexron III, or equivalent)
and free of air by using the air bleeder ass’y (704153) on a weekly basis.
*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable
tool manuals and nose assembly data sheets prior to operating tools.
*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws
ride on with light machine oil on a daily basis.
*All Screwed End Caps, Base Covers, Air Fittings, Actuators, Screws and Nose Assemblies are to be examined at the
end of each working shift to check that they are secure.
*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).
*For a complete overhaul, tool kit GB704TK is recommended.