ELECTRIC TURBO OVEN
FTE 300-240-150-120
Electrical extension cords or the like:
for no reason whatsoever should you connect any
other equipment to the same wall socket. That can cause an overload on the electrical supply
and/or bad contact. Overloads can cause prejudicial heating to insulation of the connections,
the terminals or surroundings of the conductors, and cause damages and it may even burn the
installations or the product.
Power oscillations:
if power supply in your establishment presents any oscillations that
are not compliant with the variations allowed, contact your power supplier and ask for its
regularization. If that is not possible, install an automatic stabilizer according to the maximum
nominal power.
Water supply:
it
is
necessary
to
have
a
fix
point
for the water supply, preferably an
exclusive
one
and
that
meets
technical
specifications
for
pressure.
Adapt
a
valve
o
a
garden-lik
faucet
with a
3/4”BSP
thread.
1. Provide for installation site:
- Box with fuse and circuit breaker.
- Electric wall socket check power supply: wall socket.
- Grounding wire check power supply: wall socket.
- Water supply point with valve
- Always allow a 20-cm clearance between oven and walls in order to
obtain a good performance from your oven and to make sure there is no
overheating of the motor.
- Observe direction of motor rotation. Correct direction is counterclockwise.
2. Perfect leveling of the equipment should be observed.
HYDRAULIC SUPPLY
INSTALLING
ATTENTION!
1) ) LEVELING:
The oven is equipped with casters so that it is easier to move it around, and a screw to
adjust height.
CONTROLS
2) STEAM CIRCUIT
The electronic controller is equipped with a “timer” that controls how long the solenoid
valve is to be kept open when operated manually. Time is programmed by the user. (Check
electronic controller configurations steam time).
After time controlled by the “timer” is over, LED turns off automatically, indicating that
solenoid valve has closed, and not allowing any more water to come in.
Wait for 10 seconds, and then press steam key again in order to repeat steam cycle. If
water pressure is too high, a volume of water above necessary will come in.
ELECTRIC TURBO OVEN
FTE 300-240-150-120
Time and Temperature:
Press the key and hold until the upper display flashes, use the
and to regular keys as your product. Press again to a key and hold until the lower display
flashing, use the keys and to make your schedule to record your programming press the
key again.
.
NOTE:
During programming, if there is a pause longer than 3 seconds, equipment will resume
regular control condition.
Steam Time:
To adjust the steam time, press the , and to access programming,
and or keys to set the desired value.
Turbine:
Turbine will activate itself 3 seconds after
Emergency Switch key
and
ON / OFF
Switch key
have been pressed.
* Following sequence described above, burner flame wil l light up and go out automatically ,
always keeping temperature that was programmed.
To set a new configuration, proceed as follows:
1- First of all, check whether the oven has been properly plugged to electricity
2- Press
“On/Off”.
3- At this moment, controller will perform automatic ignition of the burner, and display
will exhibit the configurations set at the factory.
4
SEQUENCE TO TURN OVEN ON:
When oven has reached the temperature desired, proceed as follows:
1- Open oven door. At this moment, micro switch key will automatically turn turbine off.
2- Load batch and close the door. 3 seconds after you have closed the door, turbine will
turn on.
3- Press “STEAM” switch key . At this moment, solenoid valve will open letting water into
the chamber for the time programmed.
4- Program cooking time on the display.
5- Activate switch key .
6- Wait for sound signal given by the alarm, which should signalize cooking time determined
on the “timer” is over.
PASTRY:.......................................120 A 180ºC
SWEET ROLLS: ..........................150ºC
FRENCH ROLLS:.........................175ºC
ATTENTION: Temperatures should not be higher than the ones specified below;
otherwise you might not reach the results you expected.
For good functioning and long useful life do not use your oven at temperatures
higher than 250°C.
TEMPERATURES
COOKING
6
2
Two halogenous 50W-12V lamp bulbs are used to illuminate the internal chamber of the
oven. To replace the bulbs, just remove setscrews tha t hold the glass pane of the door.
Disconnect the lamps from their plugs, and put new ones there.
Note:
Install l
amp
bulbs
with clean hands to prevent dirt or grease from sticking to their
glass.
ILLUMINATION OF THE OVEN
17
22
6
5
2
3
5
5
6
5
4
6
Summary of Contents for FTE 120
Page 2: ......
