Future Design FDC-9300, User Manual

Page: 46 / 52

Triac ( SSR ) Output Triac ( SSR ) Output
Rating :
Inrush Current :
Min. Load Current :
Max. Off-state Leakage :
Max. On-state Voltage :
Insulation Resistance :
Dielectric Strength : 1A / 240 VAC
20A for 1 cycle
50 mA rms
3 mA rms
1.5 V rms
1000 Mohms min. at 500 VDC
2500 VAC for 1 minute
Rating :
Inrush Current :
Min. Load Current :
Max. Off-state Leakage :
Max. On-state Voltage :
Insulation Resistance :
Dielectric Strength : 1A / 240 VAC
20A for 1 cycle
50 mA rms
3 mA rms
1.5 V rms
1000 Mohms min. at 500 VDC
2500 VAC for 1 minute
DC Voltage Supply Characteristics ( Installed at Output 2 ) DC Voltage Supply Characteristics ( Installed at Output 2 )
Type Tolerance Max. Output
Current
Max. Output
Current
Ripple
Voltage Ripple
Voltage
Isolation
Barrier Isolation
Barrier
20 V 20 V +/-0.5 V +/-0.5 V 25 mA 25 mA
0.2 Vp-p 0.2 Vp-p
500 VAC 500 VAC
500 VAC 500 VAC
500 VAC 500 VAC
12 V 12 V +/-0.3 V +/-0.3 V 40 mA 40 mA
0.1 Vp-p 0.1 Vp-p
5 V 5 V +/-0.15 V +/-0.15 V 80 mA 80 mA
0.05 Vp-p 0.05 Vp-p
Alarm 1/ Alarm 2 Alarm 1/ Alarm 2
Alarm 1 Relay :
Alarm 2 Relay :
Alarm Functions :
Alarm Mode :
Dwell Timer :
Form A or Form B, Max. Rating
2A/240VAC, life cycles 100,000 for
resistive load.
Form A, Max. rating 2A/240VAC,
life cycles 200,000 for resistive load.
Dwell timer,
Deviation High / Low Alarm,
Deviation Band High / Low Alarm,
PV1 High / Low Alarm,
PV2 High / Low Alarm,
PV1 or PV2 High / Low Alarm,
PV1-PV2 High / Low Alarm,
Loop Break Alarm,
Sensor Break Alarm.
Normal, Latching, Hold, Latching / Hold.
0 - 6553.5 minutes
Alarm 1 Relay :
Alarm 2 Relay :
Alarm Functions :
Alarm Mode :
Dwell Timer :
Form A or Form B, Max. Rating
2A/240VAC, life cycles 100,000 for
resistive load.
Form A, Max. rating 2A/240VAC,
life cycles 200,000 for resistive load.
Dwell timer,
Deviation High / Low Alarm,
Deviation Band High / Low Alarm,
PV1 High / Low Alarm,
PV2 High / Low Alarm,
PV1 or PV2 High / Low Alarm,
PV1-PV2 High / Low Alarm,
Loop Break Alarm,
Sensor Break Alarm.
Normal, Latching, Hold, Latching / Hold.
0 - 6553.5 minutes
Data Communication Data Communication
Interface :
Protocol :
Address :
Baud Rate :
Data Bits :
Parity Bit :
Stop Bit :
Communication Buffer : RS-232 ( 1 unit ), RS-485 ( up to 247 units )
Modbus Protocol RTU mode
1 - 247
0.3 ~ 38.4 Kbits/sec
7 or 8 bits
None, Even or Odd
1 or 2 bits
50 bytes
Interface :
Protocol :
Address :
Baud Rate :
Data Bits :
Parity Bit :
Stop Bit :
Communication Buffer : RS-232 ( 1 unit ), RS-485 ( up to 247 units )
Modbus Protocol RTU mode
1 - 247
0.3 ~ 38.4 Kbits/sec
7 or 8 bits
None, Even or Odd
1 or 2 bits
50 bytes
Analog Retransmission Analog Retransmission
Functions :
Output Signal :
PV1, PV2, PV1-PV2, PV2-PV1, Set Point,
MV1, MV2, PV-SV deviation value
4-20 mA, 0-20 mA, 0 - 1V, 0 - 5V,
1 - 5V, 0 - 10V
Functions :
Output Signal :
PV1, PV2, PV1-PV2, PV2-PV1, Set Point,
MV1, MV2, PV-SV deviation value
4-20 mA, 0-20 mA, 0 - 1V, 0 - 5V,
1 - 5V, 0 - 10V
Resolution :
Accuracy :
Load Resistance :
Output Regulation :
Output Settling Time :
Isolation Breakdown Voltage :
Integral Linearity Error :
Temperature Effect : +/-
Saturation Low :
Saturation High :
Linear Output Range :
15 bits
+/-0.05 % of span +/-0.0025 % / C
0 - 500 ohms ( for current output )
10 K ohms minimum ( for voltage output )
0.01 % for full load change
0.1 sec. (stable to 99.9 % )
1000 VAC min.
+/-0.005 % of span
0.0025 % of span/ C
0 mA ( or 0V )
22.2 mA ( or 5.55V, 11.1V min. )
0-22.2mA(0-20mA or 4-20mA)
0-5.55V ( 0 - 5V, 1 - 5V )
0 - 11.1 V ( 0 - 10V )
Resolution :
Accuracy :
Load Resistance :
Output Regulation :
Output Settling Time :
Isolation Breakdown Voltage :
Integral Linearity Error :
Temperature Effect : +/-
Saturation Low :
Saturation High :
Linear Output Range :
15 bits
+/-0.05 % of span +/-0.0025 % / C
0 - 500 ohms ( for current output )
10 K ohms minimum ( for voltage output )
0.01 % for full load change
0.1 sec. (stable to 99.9 % )
1000 VAC min.
+/-0.005 % of span
0.0025 % of span/ C
0 mA ( or 0V )
22.2 mA ( or 5.55V, 11.1V min. )
0-22.2mA(0-20mA or 4-20mA)
0-5.55V ( 0 - 5V, 1 - 5V )
0 - 11.1 V ( 0 - 10V )
User Interface User Interface
Dual 4-digit LED Displays :
Keypad :
Programming Port :
Communication Port :
Upper 0.4" ( 10 mm ),
Lower 0.3 " ( 8 mm )
3 keys
For automatic setup, calibration
and testing
Connection to PC for
supervisory control
Dual 4-digit LED Displays :
Keypad :
Programming Port :
Communication Port :
Upper 0.4" ( 10 mm ),
Lower 0.3 " ( 8 mm )
3 keys
For automatic setup, calibration
and testing
Connection to PC for
supervisory control
Control Mode Control Mode
Output 1 :
Output 2 :
ON-OFF :
P or PD :
PID :
Cycle Time :
Manual Control :
Auto-tuning :
Self-tuning :
Failure Mode :
Sleep Mode :
Ramping Control :
Power Limit :
Pump / Pressure Control :
Adaptive Heat-Cool Dead Band :
Remote Set Point :
Differential Control :
Reverse ( heating ) or direct ( cooling )
action
PID cooling control, cooling P band 1~
255% of PB
0.1 - 100.0 ( LF ) hysteresis control
( P band = 0 )
0 - 100.0 % offset adjustment
Fuzzy logic modified
Proportional band 0.1 ~ 900.0 F.
Integral time 0 - 1000 seconds
Derivative time 0 - 360.0 seconds
0.1 - 100.0 seconds
Heat (MV1) and Cool (MV2)
Cold start and warm start
Select None and YES
Auto-transfer to manual mode while
sensor break or A-D converter damage
Enable or Disable
0 - 900.0 F/minute or
0 - 900.0 F/hour ramp rate
0 - 100 % output 1 and output 2
Sophisticated functions
provided
Self adjustment
Programmable range for voltage
or current input
Control PV1-PV2 at set point
Output 1 :
Output 2 :
ON-OFF :
P or PD :
PID :
Cycle Time :
Manual Control :
Auto-tuning :
Self-tuning :
Failure Mode :
Sleep Mode :
Ramping Control :
Power Limit :
Pump / Pressure Control :
Adaptive Heat-Cool Dead Band :
Remote Set Point :
Differential Control :
Reverse ( heating ) or direct ( cooling )
action
PID cooling control, cooling P band 1~
255% of PB
0.1 - 100.0 ( LF ) hysteresis control
( P band = 0 )
0 - 100.0 % offset adjustment
Fuzzy logic modified
Proportional band 0.1 ~ 900.0 F.
Integral time 0 - 1000 seconds
Derivative time 0 - 360.0 seconds
0.1 - 100.0 seconds
Heat (MV1) and Cool (MV2)
Cold start and warm start
Select None and YES
Auto-transfer to manual mode while
sensor break or A-D converter damage
Enable or Disable
0 - 900.0 F/minute or
0 - 900.0 F/hour ramp rate
0 - 100 % output 1 and output 2
Sophisticated functions
provided
Self adjustment
Programmable range for voltage
or current input
Control PV1-PV2 at set point
Digital Filter Digital Filter
Function :
Time Constant : First order
0, 0.2, 0.5, 1, 2, 5, 10, 20, 30, 60
seconds programmable
Function :
Time Constant : First order
0, 0.2, 0.5, 1, 2, 5, 10, 20, 30, 60
seconds programmable
Resolution : Resolution :
15 bits 15 bits
Output Regulation :
Output Settling Time :
Isolation Breakdown Voltage :
Temperature Effect : 0.01 % for full load change
0.1 sec. ( stable to 99.9 % )
1000 VAC
+/-0.0025 % of SPAN / LC
Output Regulation :
Output Settling Time :
Isolation Breakdown Voltage :
Temperature Effect : 0.01 % for full load change
0.1 sec. ( stable to 99.9 % )
1000 VAC
+/-0.0025 % of SPAN / LC
Linear Output Linear Output
UM9300 2.0 UM9300 2.0
46