background image

9

Safety Precautions

Other Safety Precautions

CAUTION

When operating two or more models at the same time, have a third person act as a spotter. They will 
be in charge of safety and you should follow their instructions.

Beginners should receive instructions regarding safety and operation from an experienced modeler. 

Always use only genuine Futaba transmitter, receivers, servos, and electronic speed controls, along 
with other optional parts and components. 
Futaba will not be held responsible for damages caused by other than genuine Futaba parts and 
components. Use only genuine Futaba parts and components listed in the instruction manual and 

catalog.

Do not short circuit the Ni-Cd/Ni-MH battery terminals. 
Short circuiting the terminals will lead to sparks and overheating and could cause a fire and burns as 

well. 

Do not expose plastic parts to fuel, motor spray, waste oil or exhaust.

The fuel, motor spray, waste oil and exhaust will penetrate and damage the plastic.

<Ni-Cd/Ni-MH Battery Electrolyte>

The electrolyte in Ni-Cd/Ni-MH batteries is a strong alkali. Should you get even the smallest amount of the 
electrolyte in your eyes, DO NOT RUB. Wash immediately with water and seek medical attention at once. 
The electrolyte can cause blindness. If electrolyte comes in contact with your skin or clothes, wash with 
water immediately.

CAUTION 

Do not store your R/C system where it will be exposed to the following conditions.

• Extreme heat or coldness 
• Exposed to direct sunlight
• Where humidity is high
• Where vibration is prevalent
• Where dust is prevalent
• Where there is steam and condensation

Storing your R/C system under adverse conditions could cause deformation and numerous other 

problems with operation.

If the system will not be used for a long period of time, remove the batteries from the model and store 
in a cool, dry place.

If the batteries are left in the model, electrolyte may leak and damage the model.

<Ni-Cd/Ni-MH Battery Recycling>

A used Ni-Cd/Ni-MH battery is valuable resource. Insulate the battery terminals and dispose of the battery 
by taking it to a battery recycling center.

Summary of Contents for 2HR































Reviews: