Furuno FAR-2157 Installation Manual Download Page 17

Page: 17 / 111

1-9

Fastening monitor unit to hanger

Attaching hand grips

Hand grips are optionally available for the desktop-mount monitor unit. Attach them as follows:

1. Remove the snap buttons attached at step 5 on the previous page.
2. Fix hand grips with wave washers, rosette washers and flat head screws.

How to attach hand grips

Attaching hood

When it is too bright in the daytime, use the optional hood (Type: FP03-11500, Code No.: 001-

020-090) to shade the screen.

Contents of hood

Name

Type

Code No.

Qty.

Hood

FP03-11501

001-020-120

Fixing plate

03-163-2202-0

100-335-560-10

Screw

M4x10 D=13 US304

000-862-543

Panel cover

Hex bolt
(M6x25)

Hanger (R)

Hanger stay

M12 bolts for fixing
(Dockyard supply)

Hanger (L)

Hex bolt
M10x30

Snap button

Hole plug

Panel cover

To remove this, insert fingernail in groove.

Flat Washer M10

Spring Washer M10

Hand grip

Flat head screw (torque: 7.6 Nm)

Wave washer

Rosette washer

Summary of Contents for FAR-2157
















































































































Search results

Summary of Contents for FAR-2157

Reviews:

Related manuals for FAR-2157

Brands by name

Popular brands

Furuno FAR-2157, Installation Manual

Search results

Summary of Contents for FAR-2157

Reviews:

Related manuals for FAR-2157

Brands by name

Popular brands