Funke TRT800A-OLED Operation And Installation Download Page 25 | Manualshive

Page: 25 / 48

background image

TRT800A / P/N 800ATC-A-(2xx)-(3xx)

Operation and Installation

24

Document-No: 03.2114.010.71e / Revision: 2.20

3.8 Antenna

3.8.1 Antenna Selection

•

Recommended antennas: see section 3.11 Accessories

•

Choose an antenna type compatible with the vehicle and the

mounting location.

•

Specified features depend on proper installation of the antenna.

•

The radiation pattern needs to be verified considering aircraft type

and mounting location.

•

The electrical interference between the antenna and any other

equipment must be taken into account in such a way that no
reduction of the performance of any other system will occur.

•

Install only certified antennas!

3.8.2 Installation Recommendation

•

Take note of the antenna manufacturer’s instructions.

•

The usually deployed Dipole- or Blade antennas necessarily

require a high frequency capable solid metal ground plane at the
antenna base.

•

For installation in composite aircrafts, ground planes are to be

added. The ground plane should be as large as possible but in any
case not smaller than 10 cm x 10 cm. If in doubt, please contact
the aircraft manufacturer.

•

Keep away three feet from any other antenna.

•

Pursue mounting in vertical position under the belly in flight

direction.

3.8.3 Antenna Wiring

•

Suitable antenna cables: see section 3.11 Accessories

•

Keep wiring as short as possible.

•

The smallest cable bend radius is 10cm. Avoid sharp bends.

•

Keep away from an ADF antenna cable at least 12 inches.

•

Electrical connections to the antenna shall be protected against

moisture to avoid loss of efficiency.

«
...
23
24
25
26
27
...
»

Summary of Contents for TRT800A-OLED

















































Reviews:

No comments

Related manuals for TRT800A-OLED

Brand: Danelec Pages: 67

Brand: Garmin Pages: 2

Brand: Icom Pages: 2

Brand: Xoro Pages: 32

P3 Player FM RADIO EARPHONE

Brand: X-Micro Pages: 2

SureCross DX80ER M-H Series

Brand: Banner Pages: 3

Brand: EisSound Pages: 21

Brand: Benthos Pages: 68

Brand: GME Pages: 33

Brand: E2S Pages: 20

Brand: GPX Pages: 2

Alphatron Marine Mode Switch 3 Pos

Brand: JRC Pages: 12

Brand: Seiwa Pages: 8

Brand: Reely Pages: 88

Brand: Sangean Pages: 1

Brand: Sangean Pages: 1

Brand: Sangean Pages: 1

Brand: Sangean Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands