Functional Cosmetics Company SweatStop DE20 Instruction Manual Download Page 11

11

EN

SweatStop® DE20 – Revison 002b – 2019-12-09

SweatStop® DE20

Application

Basics

Tap water iontophoresis is used for the temporary relief of the hyperhidrosis affecting the palms 

of hands and feet and the underarms. The chances to reduce the perspiration to a normal level 

without damaging the perspiratory glands are very high. This effect is achieved by running an 

electric current (constant or pulsed) through the affected body parts to accustom the cells to 

electric stimulation. As a result, the sweat glands will be slower to react to their own stimulation. 

Since the glands are “only” familiarised with electric stimulation, their original condition will  

return relatively fast once the treatment is discontinued!

As a rule of thumb, conduct a daily initial therapy until you observe a significant effect (without 

skin irritations). Once positive results are registered, you can start to pause the daily treatment. 

Since the causes of hyperhidrosis differ between patients, you will have to adjust the therapy to 

your individual needs and lifestyle. These factors may vary according to yearly seasons and every-

day occurrences. 

Before you commence the session, take off all metal accessories (e.g. jewellery). Clean the skin in 

the treatment areas. Remove all ointments, lotions and cosmetics.

Exception: 

All damages to the skin (minor injuries, scratches etc.) must be coated with vaseline  

or a fatty lotion before the treatment to avoid further injuries. Damaged skin parts have an  

especially high current permeability and offer a greater risk of injury. The “entirety” of the current 

will run “only” through the damaged skin. Please only cover the spots affected by injury – caution 

is advised, since vaseline and other fatty lotions block the current flow and impede the therapeutic 

effect. 

The device monitors the skin resistance and the electric conductivity of the water in order to  

reduce the strain (anti-overtreatment protection). 

If your tap water is very hard, an addition of cooking salt may help increase the conductivity. 

Summary of Contents for SweatStop DE20





























Reviews: