manualshive.com logo in svg

Full Spectrum Laser HL40-5g Hobby Advanced, User Manual, Page: 49 / 91

Share
Download
Full Spectrum Laser HL40-5g Hobby Advanced User Manual Download Page 49

          48 

TOP LINE MENUS (LEFT SIDE) 

FILE  

The File menu allows the user to open up files to engrave. RetinaEngrave supports drag and drop 
of .xps files for vector cutting and standard image file types (.bmp, .jpg, .png, .tiff) for raster 
engraving. Other file types must be printed to the Full Spectrum Engineering Driver or saved as 
.xps documents. The file menu also allows a user to load or save a project and settings. 

File sub­menus 

Save Project 
Open Project Settings Only 
Options 
Clear Workspace

 

The File sub­menu allows you to save your workspace window setup, set the PC to audibly alert 
when a job is completed, enable or disable the keyboard shortcuts, load the last­saved project on 
startup or log output for troubleshooting. Note that adjustments made to the designs scale or stroke 
color while in RE cannot be saved. Designs need to be at the desired scale and stroke color before 
being brought into RE. 

 
LASER 

The Laser menu provides options related to the laser unit configuration and communications. It will 
allow you to select the type of laser you are connected to, manually reconnect to the laser or 
manually set the connection IP address. 

Laser sub­menus: 

Change Laser Profile 
Firmware (Update) 
RetinaEngrave Card Commands 
Configure Static IP Address 
Specify IP Address for Connection 
Save Job as Binary File  
Send Binary to USB 
Save and Send Current Job to USB 
Material and Focus Tests 

The Laser sub­menu allows you to save the current job and settings as a .bin file onto a USB 
device (when the device is loaded onto the laser). 

 

CAUTION! The “RetinaEngrave Card Commands sub­menu option should only be 
accessed under supervision of Full Spectrum Laser support staff. 

 
 
Technical Support is available from 8:00 am (PST) to 5:00 pm (PST) Monday through Friday at 

[email protected]

​

. 

Summary of Contents for HL40-5g Hobby Advanced




























































































Reviews:

No comments