manualshive.com logo in svg

Fujitsu PRIMERGY S60, Manual, Page: 80 / 99

Share
Download
Fujitsu PRIMERGY S60 Manual Download Page 80

72

 

 U41221-J-Z156-1-74

Problem Solutions and Tips

Troubleshooting

Power supply units defective

Ê

Check the LEDs of the power supply units.

If the operating indication (green LED) on the power supply units is dark and 
the fault indication (amber LED) is on, the power supply units are defective.

Ê

Replace the power supply units.

11.1.1.2 Power supply status indicator lights yellow

One of the installed power supply units has failed.

Ê

Check which one of the power supply units has failed. If only the amber LED 
is on, the power supply unit is defective or the power supply don’t receive 
power.

Ê

Replace the defective power supply unit (see section “Replacing the Power 
Supply Unit” on page 30).

The problem is cleared if:

–

the green LED on the power supply unit is ON and

–

the power supply status indicator on the front of the storage subsystem 
lights green.

11.1.1.3 Power supply status indicator lights orange

The device is switched OFF and in the standby mode.

Ê

Switch the device ON (see section “Switching the Storage Subsystem 
ON/OFF” on page 69).

Ê

If the LED remains orange, the power supply units may have failed. Replace 
the power supply units. If the LED then still remains orange, contact our 
Service organization.

Summary of Contents for PRIMERGY S60




































































































Reviews:

No comments