manualshive.com logo in svg

Fujitsu PRIMERGY S60, Manual, Page: 42 / 99

Share
Download
Fujitsu PRIMERGY S60 Manual Download Page 42

34

 

 U41221-J-Z156-1-74

Installing/Removing the Fan Module

Fan Module

6.1

Installing/Removing the Fan Module

I

Please note the status of the fan LED before removing and after installing 
the fan module (3) (see section “Fan LED” on page 23).

Floorstand model

Ê

Remove the left side cover (see section “Removing/Mounting the left Side 
Cover” on page 26).

Rack model

Ê

Loosen the two knurled screws on the front of the rack model and pull out 
the storage subsystem from the rack.

Figure 13: Releasing and Removing the Fan Module

Ê

Release the fan module by putting two fingers into the recessed grips and 
push the locking mechanisms found here inwards (1). 

V

CAUTION!

Note the warning label “Rotating Parts“ (4) on the fan module. There 
is an increased risk of injury from rotating parts. 

Ê

Remove the fan module from the storage subsystem in the direction of the 
arrow (2).

3

1

1

2

4

Summary of Contents for PRIMERGY S60




































































































Reviews:

No comments