manualshive.com logo in svg

Fujitsu PRIMERGY S60, Manual, Page: 76 / 99

Share
Download
Fujitsu PRIMERGY S60 Manual Download Page 76

68

 

 U41221-J-Z156-1-74

Connecting and Disconnecting Cables

Installation

10.5

Connecting and Disconnecting Cables

V

CAUTION!

The power plug must be pulled out!

Read the documentation for the external device before connecting any 
cables.

Cables may neither be connected nor disconnected during thunder-
storms.
When disconnecting a cable, always hold it by the plug, never pull on the 
wire!

When connecting or disconnecting cables, follow the sequence 
described below:

Connecting leads

Ê

Switch off all the relevant devices.

Ê

Pull the power plugs of all the relevant devices out of their sockets.

Ê

Connect all the cables to the server and the storage subsystem. Mark the 
cables and make a note of the function of each cable. Always note the safety 
instructions in chapter “Important Notes” on page 7.

Ê

Connect the power plugs to appropriately properly grounded power outlets. 
For rack models make sure that the power cables of the devices are 
connected in such a way that a even distribution of power to the three 
phases (L1, L2, L3) in the rack is achieved (you can find further information 
in the manual for the corresponding rack).

Ê

For devices mounted in a rack, secure the cables to the articulated cable 
guides with cable ties.

Disconnecting leads

Ê

Switch off all the relevant devices.

Ê

Pull the power plugs of all the relevant devices out of their sockets.

Ê

Disconnect all the cables on the server and on the storage subsystem.

Summary of Contents for PRIMERGY S60




































































































Reviews:

No comments