manualshive.com logo in svg

Fujitsu PRIMERGY RX4770 M4, Operating Manual, Page: 59 / 82

Share
Download
Fujitsu PRIMERGY RX4770 M4 Operating Manual Download Page 59

RX4770 M4

Operating Manual

59

Starting up and operation

iRMC-related status signals

I

For further information, please refer to chapter "Updating or recovering 
the iRMC" in the Upgrade and Maintenance Manual.

6

AC 
connected 
indicator

green on

– The server is switched off and 

connected to the mains 
(standby mode).

– The server has been switched 

on but Power Cycle Delay 
settings delay it from turning 
on for a specified time.

I

After connecting the server 
to the mains, it will take 
about 60 seconds until the 
server will enter standby 
mode and can be switched 
on.

off

– The server is switched off and 

not connected to the mains.

– The server is switched on and 

operating normally.

ID indicator

Global error 
indicator

Description

blue flashing

off

A remote connection has been 
established. Local VGA output has 
been disabled during the remote 
session.

blue flashing

orange flashing

An emergency flash of the iRMC 
firmware is in progress.

Pos.

Label

Indicator

Status

Description

Summary of Contents for PRIMERGY RX4770 M4



















































































Reviews:

No comments