Fujitsu Fi-718PR Operator'S Manual Download Page 15

Page: 15 / 18

fi-718PR Imprinter Operator’s Guide

| 13

4. Daily Care

4.1. Cleaning the Print Cartridge

If ink gets on the nozzle plate of the print cartridge or if the

imprinter has not been used for a long time, it may cause

low quality prints. When this happens, clean the nozzle

plate of the print cartridge.

ATTENTION

For cleaning, use a dry cloth (DO NOT use tissues), and gently

wipe any dirt and stains off on the nozzle plate.

HINT

If the ink emission holes are still blocked after cleaning the print

cartridge, replace it with a new cartridge.

1. Turn off the scanner.

2. Remove the print cartridge.

(Refer to “

3.4. Replacing the Print Cartridge

”)

ATTENTION

Be careful not to touch the nozzle plate or the contact part

with your hand.

3. Gently wipe off the ink on the nozzle plate.

4. Confirm that the print cartridge is clean, and then

install the print cartridge.

(Refer to “

3.4. Replacing the Print Cartridge

”)

ATTENTION

When installing the print cartridge, install it properly.

4.2. Cleaning the Imprinter

After frequent use, the waste ink will begin to accumulate

on the base surface of the print cartridge holder, which can

soil printouts. Always maintain the base surface clean.
To assure high quality print outs and long use of the

imprinter, adopt a daily maintenance procedure as given

below.

ATTENTION

When cleaning, use an absorbent cloth or a waste cloth to wipe

the ink off the surface of the base.

If the ink has dried, wipe it lightly with a water-moistened cloth

as the ink is water-based.

1. Turn off the scanner.

2. Remove the print cartridge.

(Refer to “

3.4. Replacing the Print Cartridge

”)

3. Open the print section.

4. Dab the surface of the base of the print cartridge

with a cloth or waste cloth to remove the ink.

ATTENTION

Be careful not to touch the metal wheels located behind the

upper rollers in the print section.

5. Confirm that the print section is clean, and then

close the print section.

6. Reinstall the print cartridge and close the print

cartridge cover.

(Refer to “

3.4. Replacing the Print Cartridge

”)

Nozzle plate

Summary of Contents for Fi-718PR



















Search results

Summary of Contents for Fi-718PR

Reviews:

Related manuals for Fi-718PR

Brands by name

Popular brands

Fujitsu Fi-718PR, Operator'S Manual

Search results

Summary of Contents for Fi-718PR

Reviews:

Related manuals for Fi-718PR

Brands by name

Popular brands