manualshive.com logo in svg

Fujitsu C150-E146-02EN, Operator'S Manual

Share
Download
Fujitsu C150-E146-02EN Operator'S Manual Download Page 67

 6-4

 

Reading Mode Setting When the Video Interface Option is Installed

This section describes the button specifications and setup details for each of the simplex (front-side),
duplex (front-side) and duplex (back-side) reading modes when the scanner has the video interface
option in the third party .
When reading mode is set by the command from the host computer, the following button operation is
not required.

 NOTE

When the video interface option is installed in the scanner, the scanner automatically recognizes the
board and changes the display.

At any time you press 

, scanner returns to screen M1

1

 Turn the power ON and verifty that
“Scanner Ready” is displayed on LCD.

2

Press 

 then the scanner displays

Screen M2.

3

Press 

 then the scanner displays

Screen 1.

4

Select ADF or FB by pressing 

 or 

then press 

. The scanner displays

Screen 2.

5

Select “Simplex” or “Duplex” by pressing

 or 

. Then press Enter. The scanner

displays Screen 3.

<Screen M1>

<Screen M2>

<Screen 1>

<Screen 2>

Summary of Contents for C150-E146-02EN





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands