Fujitsu C150-E146-02EN Operator'S Manual Download

Page: 15 / 100

1-3

No.

Function

Document cover

Closes over and keeps in place document to be read.

Document bed

Holds document to be read. Also called the Flatbed (FB).

Document holding pad

Presses a document to the Document bed.

Automatic document feeder (ADF)

Automatically feeds documents to the reading position.

Stacker

Stacks the read documents.

Power switch

Turns the power on or off.

Operator panel

Contains indicator panel that indicates scanner status.

ADF paper chute

Holds documents to be fed by the automatic document

feeder (ADF).

ADF lever

Opens or closes ADF to enable removal of documents

jammed in the feeder.

Power inlet

Connects to an AC power outlet with the power cable.

Interface connectors

Connects to the host system with interface cables.

Third party slot

A Fujitsu Video Interface Option Board is installed.

Summary of Contents for C150-E146-02EN





































































































Search results

Summary of Contents for C150-E146-02EN

Reviews:

Related manuals for C150-E146-02EN

Brands by name

Popular brands

Fujitsu C150-E146-02EN, Operator'S Manual

Search results

Summary of Contents for C150-E146-02EN

Reviews:

Related manuals for C150-E146-02EN

Brands by name

Popular brands