Fujitsu C150-E146-02EN Operator'S Manual Download Page 52

Page: 52 / 100

4-3

CAUTION

As there is always an off chance a document may be damaged using the
ADF, important original documents should never be fed through the ADF.
Instead, read manually in flatbed mode.

NOTICE

When scanning a translucent document, set the density to light mode.

NOTICE

Carbonless papers have a chemical composition that damages the Pad and Pick roller. Therefore, note
the following:

Cleaning:

If miss pick occur frequently, clean the Pad and Pick roller in accordance with the
“Cleaning and Maintenance” manual.

Replacement of parts: The life of the Pad and Pick roller may be shorter than if PPC paper documents

are fed.

NOTICE

• The leading edge of all documents fed by ADF should be straightened so the curl of the paper

meets the specifications shown below:

Less than
3 mm

Feed direction

Less than
5 mm

Top of the paper

More than
30 mm

Read surface

More than
30 mm

Summary of Contents for C150-E146-02EN





































































































Search results

Summary of Contents for C150-E146-02EN

Reviews:

Brands by name

Popular brands

Fujitsu C150-E146-02EN, Operator'S Manual

Search results

Summary of Contents for C150-E146-02EN

Reviews:

Brands by name

Popular brands