Fujitsu AOHG12LALL Installation Manual Download Page 12

Page: 12 / 19

En-11

6.1. Wiring system diagram

Connection cable to outdoor unit or BRANCH BOX

INDOOR UNIT

OUTDOOR UNIT or

BRANCH BOX

TERMINAL

Type 60245 IEC57

Cable size 1.5 mm

(Inter-unit)

Power lines

Grounding line

Power line

Control line

Please connect it to

the specified terminal.

Wired remote controller cable

*Ground the remote controller

(Please connect it when necessary.)

Red

White

Black

Indoor

unit side

CAUTION

Tighten the indoor unit connection cable and power supply indoor and outdoor unit,

branch box terminal board connections firmly with the terminal board screws. Faulty

connection may cause a fire.

If the indoor unit connection cable and power supply are wired incorrectly, the air

conditioner may be damaged.

Connect the indoor unit connection cable by matching the numbers of the outdoor,

branch box and indoor units terminal board numbers as shown in terminal label.

Earth both the indoor and outdoor, branch box units by attaching a earth cable.

Unit shall be grounded in compliance with the applicable local and national cables.

CAUTION

Be sure to refer to the above diagram for do correct field wiring. Wrong wiring causes

malfunction of the unit.

Check local electrical rules and also any specific wiring instructions or limitation.

6.2. Connection cable preparation

Keep the earth wire longer than the other wires.

Power supply cable

or connection cable

30mm

Earth wire

• Use a 4-core wire cable.

6.3. Connection of wiring

(1) Remove the control box cover from the control box.

Screw

Control box cover
Remove the 4 screws

and remove the control

box cover from the

control box.

(2) Cable connection

• C

onnect the connection cable to the terminal board.

• Connect the remote controller cable to the terminal board.

• Fix the remote controller cable to the control box cover with a nylon clamp.

Remote controller cable

1: Red

2: White

3: Black

Earth

Binder (Medium)

(Accessories)

Power supply cable

Binder (Medium)

(Accessories)

Remote controller cable

Power supply cable

9374815173-04_IM.indb 11

9/21/2011 1:45:24 PM

Summary of Contents for AOHG12LALL




















Search results

Summary of Contents for AOHG12LALL

Reviews:

Related manuals for AOHG12LALL

Brands by name

Popular brands

Fujitsu AOHG12LALL, Installation Manual

Search results

Summary of Contents for AOHG12LALL

Reviews:

Related manuals for AOHG12LALL

Brands by name

Popular brands