81
80
Explanation
Warning Displayed
Remedy
i
DPOF settings are already
specified.
i
The DPOF file contains an error or
was specified on another device.
To create the DPOF file again and reset all the
DPOF settings, press the “MENU/OK” button.
1000 or more prints were specified
in the DPOF frame settings.
The maximum number of frames for which
printing can be specified on the same xD-
Picture Card is 999. Set no more than 999
frames.
Camera malfunction or fault.
i
Switch the camera on again taking care not
to touch the lens.
i
Switch the camera on and off again several
times. If that does not remedy the problem,
contact your FUJIFILM dealer.
The lens cover is faulty.
i
Switch the camera on again, taking care not
to touch the lens.
i
Switch the camera off and on again.
The timing for recording was
incorrect because the media was
formatted on a computer.
Use a media that was formatted on the
camera.
You tried to shoot a movie when the
Microdrive was too hot.
Switch the camera off and stop using it for
about 30 minutes until it has cooled down.
Note that you can still shoot still images during
this time.
Warning Displays
e
The table below lists the warnings that are displayed on the LCD monitor
Warning Displayed
Explanation
Remedy
The camera battery is low on charge.
Have spare battery ready or replace the
batteries.
X
C
(Lit red)
(Blinking red)
\
There is a strong likelihood of
camera shake because the shutter
speed is slow.
Use flash photography. However, a tripod
should be used for some scenes and modes.
Outside the AE continuous range.
The shot can be taken, but the exposure will
not be correct.
!AF
!AE
The AF (auto focus) doesn’t work
very well.
i
If the subject is too dark, take the shot at a
distance of roughly 2 meters from the subject.
i
Use AF lock to take the picture.
!AF
No media is inserted.
i
The media is not formatted
(initialized).
i
The xD-Picture Card contact area
(gold-colored area) is dirty.
i
The camera is faulty.
i
The xD-Picture Card is not loaded
correctly.
i
The xD-Picture Card contact area
(gold-colored area) is dirty.
i
The media is damaged.
i
The media format is incorrect.
i
The camera is faulty.
The media is full and no further data
can be recorded.
i
Load an xD-Picture Card in the correct
direction.
i
Load a Microdrive in the correct direction.
i
Format the media.
i
Wipe the xD-Picture Card contact area with a
soft, dry cloth. It may also be necessary to
format the xD-Picture Card. If an error message
still appears, replace the xD-Picture Card.
i
Contact your FUJIFILM dealer.
i
Push the xD-Picture Card all the way into the
slot and check that it is locked into place.
i
Wipe the xD-Picture Card contact area with a
soft, dry cloth. It may also be necessary to
format the xD-Picture Card. If an error message
still appears, replace the xD-Picture Card.
i
Contact your FUJIFILM dealer.
Erase some images or use a media that has
some available space.
i
Data cannot be recorded due to a
media fault or a problem with the
connection between the media
and the camera.
i
The image you just shot is too
large to fit in the space available
on the media.
i
Reload the media or switch the camera off
and then on again. If this does not remedy
the problem, contact your FUJIFILM dealer.
i
Use a new media.
Frame number 999-9999 has been
reached.
Use a formatted xD-Picture Card to take
pictures.
i
You attempted to play back file
that was not recorded correctly.
i
The xD-Picture Card contact area
(gold-colored area) is dirty.
i
The camera is faulty.
i
That data cannot be played back.
i
Wipe the xD-Picture Card contact area with a
soft, dry cloth. It may also be necessary to
format the xD-Picture Card. If an error message
still appears, replace the xD-Picture Card.
i
Contact your FUJIFILM dealer.
i
The voice memo file is faulty.
i
The camera is faulty.
i
The voice memo cannot be played back.
i
Contact your FUJIFILM dealer.
You attempted to erase a protected
file.
Protected frames cannot be erased. Remove
the protection using the camera on which the
protection was applied.
You attempted to erase an image
for which DPOF settings have been
specified.
Erasing the image deletes the setting from the
DPOF specifications at the same time.
