Fuji Micro Genforce Baumr-AG BM-700i User Manual Download Page 20

Page: 20 / 30

Petrol Powered Inverter Generators

E&OE

Checking and Changing Engine Oil

The product is NOT supplied with engine oil, although traces of oil from the manufacturing

process may be present. It is essential to add adequate engine oil of the correct type to the

engine before use.

Failure to add engine oil will void the product warranty

. • Always check engine oil

level when the machine is in an upright position on a flat and level surface. • Do not use used or

contaminated engine oils. • Use only engine oils of the correct type (see

Specifications

). • Perform the first oil

change within the first 20 hours of use. Subsequently, change the oil every 20 hours of use. • It is

recommended that the engine be warm, but not hot, when performing oil changes. When the oil is warm it

drains faster. • Using dirty or incorrect engine oil may cause engine damage and void any warranty • Always

use suitable tools. • Always dispose of used oil in an environmentally responsible manner and according to

regulations. • Some engines feature oil level detection, which will prevent the engine being started or

automatically stop a running engine if there is insufficient oil. •

Always check the oil level and ensure is at

or near the "MAX" indicator before using the machine

Four-stroke engines require engine oil in the crankcase for lubrication of internal components. Severe or

irreparable damage may occur if the engine is allowed to run without engine oil. The engine oil level requires

regular maintenance as per the maintenance schedule.
To check engine oil level:
1. Place the machine in

an upright position on

a flat and level

surface.

2. Remove the 2 screws

(rotate left) securing

the engine access

cover (

), and remove

the cover.

3. Clean the machine around the oil filler cap (

) so that no dirt

or other material enters the engine when the cap is removed.

4. Remove the oil filler cap (rotate left) until fully unscrewed.

The oil level is determined by how far up the dipstick oil can

be seen. To check:

a. Wipe the dipstick (

) clean with a piece of cloth or

paper.

b. Insert the dipstick into the oil filler and screw it in.
c. Remove and inspect the dipstick – the MAX oil level

is approximately the top of the patterned section (

5. Ensure that the oil level is at or just under the permissible

maximum. If the oil level is low, add additional oil until the

correct level is reached. If the oil level is too high, drain some

oil until the correct level is reached.

6. When finished, reinstall (rotate right) the oil filler cap until firm. Wipe off any residual oil from the

machine.

7. Re-install the engine access cover and secure it with the 2 screws (rotate right).

FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG