FSR
MDC – MK1 Operations Manual [
Page 22 of 28
]
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
Table of available adjustments
*Where two values are given separated by commas (eg. "Off, On" or "NTSC, PAL"), the first relates to
the setting used when '0' is sent to the unit, and the second relates to the setting used when '1' is sent to
the unit.
ADJUSTMENT
VALUES*
COMMENT
ADC Ref.
100 to 200
Adjusts maximum input RGB voltage.
Adj. Osc.
-200 to 200
Fine-adjusts Subcarrier frequency
Auto Set
0 or 1
Set to 1 to initiate AutoSet
Baud Rate
0 to 191
Actual baud rate = 230400/(n+1)
Buttons
Off, On
Off = disable front-panel
C Sync In Freq.
0 to 140
Alter to suit incoming sync frequency when using composite sync input.
CV Filter
0 to 40
Applies a variable filter to Composite Video signals.
DAC Ref.
40 to 120
Brightness level
Flicker Red.
2, 4, 6
Lines of flicker reduction
H. Soften
Off, On
On = Soften image horizontally.
ID Restrict
n
Restricts RS232 control only to those units, which have RS232 ID already set to this value.
Image Freeze
Off, On
On = Image Frozen. Do not adjust any other settings when this is active.
IR
Off, On
On = IR remote control is enabled.
Locked
Off, On
On = Disables all front-panel buttons and IR remote control functions
Overscan
Off, On
On = Overscan
Out H-Center:
n
Adjusts image left/right position
Out H-Width:
n
Adjusts image width
Out V-Center:
n
Adjusts image up/down position
Out V-Height:
n
Adjusts image height
Output Sig.
YUV, RGB
Selects appropriate output signal type.
Pan X Pos.:
n
Adjusts Pan left/right position when in Zoom mode (higher value = Panned to the right).
Pan Y Pos.:
n
Adjusts Pan up/down position when in Zoom mode (higher value = Panned to the bottom).
Reset
Off, On
On = does a reset to user settings. Automatically goes back to Off.
RGB Term.
Off, Auto
Auto = try to detect if monitor is attached, and terminate RGB appropriately.
RS232
Mouse, Control If you change this to Mouse, RS232 commands will no longer function!
RS232 ID
0 to 255
Sets the unit's RS232 identification, where multiple units are controlled from one serial port.
Sense
1 to 3
Adjusts the AutoSet feature's sensing level
Sound
Off, On
Turns the internal speaker on or off.
Store Settings
-,
*
Sets the current settings as the power-on default.
Sync In
0 to 3
0 = VGA HV, l = Grn + sy, 2 = Pin 13, 3 = Pin 15
Total Lines
Read only
Returns number of lines in PC image - including vertical blanking lines.
Vert. Freq.
Read only
Returns vertical frequency of PC image (to nearest 1 Hz).
VGA Bot/4:
n
Tells the unit where the bottom of the image is within the PC signal. (Divided by 4).
VGA Left:
n
Tells the unit where the left-hand edge of the image is within the PC signal.
VGA Store
-, *
Stores the VGA settings, so they are used in the future.
VGA Top/4:
n
Tells the unit where the top of the image is within the PC signal. (Divided by 4).
VGA Width:
n
Tells the unit how wide the image is within the PC signal.
Video Std
NTSC, PAL
Sets the video standard
Y/C Delay
0 to 3
Adjusts luminance delay relative to chrominance.
Zoom
Off, On
Turns zoom mode on and off