FSI DAT QE Series Instruction Manual Download Page 15

Page: 15 / 27

FSI®

DAT® SERIES PNEUMATIC SHELTERS

All Shelters have full privacy zipper closure and full screen zipper closure slip in and out dirty entry/clean exit doors,

high pressure and low pressure inflation deflation valves and pressure relief valves based on size of unit as

detailed below, one high pressure compressed air inflation hose with SCBA adapter w. safety cord, tie down ropes

and D

rings to tie off to, 2 upper air vents, repair kit, manual, shelter carry sleeve/bag, and a hammer. All canopy

walls are velcro

’

d to the floor air berms for air lock, and reflective striping is found on the upper air vents above

entry and exit doors.

Units can attach to a second FSI shelter or shower, if so ordered and specified. Simply inflate

the unit and commence use in approx. 1

15 minutes (size of shelter dependent).

Every shelter with a width of over 11 ft.

regardless of length and overall

size offers a top center air berm

running the entire length of the unit at the roof line and secondary full center length air berms running on

either side of the main center berm approx. 18

24" off center.

FSI offers a total of five

”

12"

diameter

lateral roof support air berms

size of shelter dependent.

FSI shelters lead the industry in terms of weight/

snow bearing capabilities/strength.

Whatever the specification at hand FSI meets and exceeds herein.

Every FSI

DAT

series shelter comes complete with electric inflator/deflator, and high pressure compressed air

fill hose and universal high pressure scba fitting.

All units supplied w. no charge redundant features allowing for

hanging undress/redress kits etc. on the inlet and

outlet side; or for use as handles in the event a victim is in such need.

All DAT

series shelters available with cross and center divider curtains, side doors, extra windows, skylights,

HVAC/clothing ducts with ties, etc. as per published FSI literature/pricing/specs.

Multiple optional accessories available inclusive of air heaters, air coolers, elevation grids, waste water pumps, etc.

available. Visit

www.fsinorth.com

FSI Valves Quantity for different units 021616

PART NUMBER

INFLATE / DEFLATE VALVE

RELIEF VALVE

HIGH PRESSURE VALVE *

SHOWERS

DAT1010S

DAT2020S

DAT3030S

DAT2525S

DAT3535S

DAT3060S

DAT4070S

DAT4099S

SHELTERS / ISOLATION SHELTERS / FIELD HOSPITAL SHELTERS OF SAME SIZE

DAT3030

DAT3015

DAT3060

DAT3370

DAT4070

DAT5672

DAT6000

DAT6012

DAT7500

INFLATE / DEFLATE VALVE

HIGH PRESSURE VALVE *

RELIEF VALVE

* FSI supplied high pressure valve to

be filled with compressed air using

only FSI supplied high pressure air fill

hose with locking connector and

universal scba adapter."

Summary of Contents for DAT QE Series




























Search results

Summary of Contents for DAT QE Series

Reviews:

Related manuals for DAT QE Series

Brands by name

Popular brands

FSI DAT QE Series, Instruction Manual

Search results

Summary of Contents for DAT QE Series

Reviews:

Related manuals for DAT QE Series

Brands by name

Popular brands