background image

V1.0  2013

Trouble Shooting

Incorrect voltage.

Check voltage jumper setting.

Check power and loose wiring.

No DC voltage to lock.

Door will not lock

Too much back 
pressure when 
power is off

PROBLEM

POSSIBLE CAUSE

SOLUTION

Incorrect wiring connection.

Security top sleeve nut higher than 
magnet surface.

Back pressure exerted on the MEM lock 
not allowing the magnetic lock to retract 
back to its original position.

Avoid applying continuous pressure on the door when 
closed. Realign the door.

Screw fix the security top sleeve nut level with surface 
with the provided key screw and apply thread-locker-glue.

Check wiring, refer to wiring instruction.

4

Accessories and Applications

MEM2400L 

(has to be ordered separately)

Adjustable L-Bracket for installation on outward opening doors with narrow header 
frames or in conjunction with Glass-Door-Bracket U-Profile.

PRODUCT DESCRIPTION

AMGB24-12

 (has to be ordered separately)

MEM2400 Anti-Tamper-Bracket

Glass-Door U-Bracket for installation on outward opening glass doors

Glass-Door “stick-on” mounting with MEM2400 Anti-Tamper-Bracket

The Glass-Door U-Bracket is used to clamp-on the MEM 
Lock as well as the Armature Plate to either a frameless 
glass door or a frameless glass header. As mentioned 
above, the adjustable L-Bracket has to be ordered 
separately and can be used on frameless glass headers. 
The product No. AMGB24-12 has one unit in the box. 
Frameless glass door and frameless glass frame as one 
door element would require 2 units of AMGB24-12 as well 
as 1 unit Adjustable L-Bracket MEM2400L.

PRODUCT DESCRIPTION

The MEM2400 Anti-Tamper-Bracket comes with the 
MEM2400LP MEM Lock as a standard fitting.
The bracket can be used for glass door “stick-on” mounting. 
We recommend 3M self adhesive tape (e.g.4910VHB or 
equivalent) and FSH Dress plate AMAB4-BC.

164

194

38.1

35

56.7

158

40

PRODUCT DESCRIPTION

Adjustable L-Bracket for narrow header door frame

The Adjustable L-Bracket is used where there is not 
enough space to install the MEM device directly to the door 
frame header. The L-Bracket acts as an extension of the 
door frame. The Adjustable L-Bracket is also used in 
combination with the Glass-Door Bracket “U-Profile” when 
the lock has to be installed onto a frameless glass header.

56.7

32

158

PART NO. AMGB24-12

Summary of Contents for MEM2400LP

Page 1: ...00LP Mechanical Electro Magnetic Lock operates on either 12 or 24 VDC It is set ex factory on 24VDC and can be changed over to 12V DC by voltage jumper selection see installation diagram When power is applied to the lock and the door is in the closed position the Armature Plate is magnetically attracted to the MEM device and both the DSS LSS switches change status to NC When pressure is applied to...

Page 2: ... C Ensure that the 2 flat washers and 1 rubber washer are in place and tighten the screw into the tapped hole of the Anti Tamper Bracket C Note The armature plate when tightened must remain flexible and be allowed to float as mentioned above 4 Install the dome nut D through the clearance hole in the door and tighten onto the Countersunk hex screw A Armature Plate Installation Instructions Spring L...

Page 3: ...n Using the template provided secure the MEM2400LP MEM Lock firmly on the door frame with the provided screws and have it checked periodically for any possible screw loosening MEM2400LP Output and Indication Status Table Condition Serial number 1 2 3 4 5 Power OFF Door Closed Power OFF Door Open Power On Door Open Power On Door Closed Power On Door Closed Tampered DSS EW1 EW2 LSS Indication on Loc...

Page 4: ... mounting with MEM2400 Anti Tamper Bracket The Glass Door U Bracket is used to clamp on the MEM Lock as well as the Armature Plate to either a frameless glass door or a frameless glass header As mentioned above the adjustable L Bracket has to be ordered separately and can be used on frameless glass headers The product No AMGB24 12 has one unit in the box Frameless glass door and frameless glass fr...

Reviews: