Frymaster LOV M3000 Technical Reference Manual Download Page 26

Page: 26 / 50

LOV

™

Generation II Technical Reference

M3000 Useful Codes

To enter any of the following codes: Press and hold

and

simultaneously for

TEN

seconds; three

chirps sounds. The computer displays

TECH MODE

. Enter the codes below to perform this function.

•

0042

–

Reset

RECOVERY FAULT CALL SERVICE

•

1658

–

Change from F° to C°.

The computer displays

off

. Turn the computer on and check

temperature to see the temperature scale. If the desired scale is not displayed, repeat.

•

3322

–

Reset Factory Menu.

The computer displays

COMPLETE

, and then

off

. (

NOTE

This will delete any hand-entered menu items.)

•

1650

–

Enter Tech Mode.

See page 1-36 to reset passwords and change fi lter pad time.

•

1212

–

Switch Between Domestic and International Menu.

The computer displays

COMPLETE

, and then

off

. (

NOTE

: This will delete any hand-entered menu items.)

•

0469

–

Reset

Filter Stat Data

The following codes require the removal and reinsertion of the J3 locator plug on the rear of the computer
before entering the code.

•

1000

–

Reset

CALL TECH

Message.

Disconnect board locator plug (J10). Reinsert plug.

Enter

1000

. Computer display switches to

off

. Remove and then restore power to the computer

using the 20-pin plug.

•

9988

–

Reset

BADCRC

Message.

Disconnect board locator plug (J10). Reinsert plug. Enter

9988

. Computer display switches to

off

. Remove and then restore power to the computer using

the 20-pin plug. Replace the computer.

The following codes are entered when prompted to do so or from an energy misconfi gured exception error.

•

1111

–

Reset

SERVICE REQUIRED

Message.

Enter this when the issue is fi xed and you

are prompted to enter.

•

1234

–

Enter

SETUP MODE

from energy misconfi gured exception error.

(This usu-

ally can be done without pressing the fi lter buttons if an error is displayed.)

Passwords

To enter level one, level two passwords –

Press and hold the

TEMP

and

INFO

buttons simultane-

ously until

level 1

level 2

is displayed. Release the buttons and

ENTER

Code

appears.

•

1234

–

Fryer Setup, Level One, and Level Two.

•

4321

– Usage Password.

Summary of Contents for LOV M3000



















































Search results

Summary of Contents for LOV M3000

Reviews:

Frymaster LOV M3000, Technical Reference Manual, Page: 26 / 50

Search results

Summary of Contents for LOV M3000

Reviews: