manualshive.com logo in svg

Frymaster LOV M3000, Technical Reference Manual, Page: 23 / 50

Share
Download
Frymaster LOV M3000 Technical Reference Manual Download Page 23

LOV

™

 Generation II Technical Reference

22

Problem

Probable Causes

Corrective Action

M3000 display shows 

RECOVERY FAULT 

RECOVERY FAULT 

CALL SERVICE.

CALL SERVICE.

Recovery time exceeded maximum 
time limit for two or more cycles.  

Silence the alarm by pressing the 

9

 

button.  Clear the error using the code 
on page 25.  Maximum recovery for 
electric is 1:40.  

M3000 display 

shows

 

ENERGY 

ENERGY 

MISCONFIGURED

MISCONFIGURED

Wrong energy type selected in 
setup.

Press 1234 to enter setup and set 
energy type for electric.

M3000 display shows 

EXCEPTION ERROR 

EXCEPTION ERROR 

with the description on the 

right.

An error has occurred.

Press 1234 to enter setup and 
recon

fi

 gure the computer.

M3000 displays 

SERVICE 

SERVICE 

REQUIRED

REQUIRED

 followed by 

the error

.

An error has occurred.

Press YES to silence alarm.  The 
error is displayed three times.  See 
list of issues on page 26.  Fix issue. 
The computer displays 

SYSTEM 

SYSTEM 

ERROR FIXED? YES/NO.

ERROR FIXED? YES/NO.

   Press 

YES.  Computer displays 

ENTER 

ENTER 

CODE

CODE

..  Enter 1111 to clear error 

code.  Pressing NO will allow the fryer 
to cook, but error will be redisplayed 
every 15 minutes.

M3000 display is in 

wrong temperature scale 

(Fahrenheit or Celsius).

Incorrect display option 
programmed.

See page 28 to change temperature 
scale. 

M3000 displays 

CHANGE 

CHANGE 

FILTER PAD

FILTER PAD

.

Filter error has occurred, 

fi

 lter pad 

clogged, 24 hour 

fi

 lter pad change 

prompt has occurred, or change 

fi

 lter pad was ignored on a prior 

prompt.

Change the 

fi

 lter pad and ensure the 

fi

 lter pan has been removed from the 

fryer for a minimum of 

30

 seconds.  

Do 

NOT

 ignore 

CHANGE FILTER 

CHANGE FILTER 

PAD

PAD

 prompts.

M3000 display shows 

INSERT pan

INSERT pan

.

A. Filter pan is not fully inserted into 

fryer.

B. Missing 

fi

 lter pan magnet.

C. Defective 

fi

 lter pan switch.

A. Pull 

fi

 lter pan out and fully reinsert 

into fryer.

B. Ensure the 

fi

 lter pan magnet is in 

place and replace if missing.

C. If the 

fi

 lter pan magnet is fully 

against the switch and computer 
continues to display 

INSERT 

INSERT 

pan

pan

, switch is possibly defective.

M3000 display shows 

hot-hi-1

hot-hi-1

.

Frypot temperature is more than 
410ºF (210ºC) or, in CE countries, 
395ºF (202ºC).

This in an indication of a malfunction 
in the temperature control circuitry, 
including a failure of the high-limit 
thermostat.  

M3000 display shows 

HI-

HI-

LIMIT

LIMIT.

Computer in high-limit test mode.

This is displayed only during a test of 
the high-limit circuit and indicates that 
the high-limit has opened properly.

Summary of Contents for LOV M3000



















































Reviews:

No comments