Frymaster LOV M3000 Technical Reference Manual Download Page 21

Page: 21 / 50

LOV

™

Generation II Technical Reference

Loading and Updating Software Procedures

Updating the software takes approximately 20 minutes. To update the software, follow these steps:

1. Switch all computers to

OFF

. Press the

TEMP

button to check current M3000/MIB/AIF/ATO software

version.

2. Remove the two screws on the left side cover plate of the M3000 board.

3. With the computer folded down, insert the SD card into the slot on the left side of the M3000. The

contacts on the card should face down and the notch should appear on the bottom right (see pictures
below).

4. Once

inserted,

UPGRADE IN PROGRESS

appears on the left display and

WAIT

on the right.

5. The display then changes to

CC UPDATING

on the left and the percentage completed appears on the

right. The display counts up to 100 on the right, changing to a fl ashing

BOOT

DO NOT REMOVE

THE CARD UNTIL THE DISPLAY PROMPTS TO DO SO IN STEP 8.

6. Then,

UPGRADE IN PROGRESS

is displayed on the left display and

WAIT

on the right again,

followed by

COOK HEX

mib HEX

aif HEX

ending with

aTO HEX

displayed on the left and

the percentage complete on the right.

7. The display then changes to

REMOVED SD CARD

on the left and

100

on the right.

8. Remove the SD card using the fi ngernail slot on the top of the SD card.

9. Once the SD card is removed the display changes to

CYCLE POWER

10. Cycle the control power using the hidden reset switch behind the right control box (see page 38).

HOLD

THE SWITCH FOR 10 SECONDS ENSURING THE MIB BOARD HAS POWERED FULLY
DOWN.

11.

M3000 CAN TX FULL

SERVICE REQUIRED

error) may appear while computers are

rebooting. Press YES at the prompt to cancel alarm. A fl ashing

BOOT

is displayed on the remaining

computers while the program is transferred.

12. When the update is complete, the M3000 displays

OFF

. The MIB display will remain blank while

software is loading, changing to show the vat numbers. Once the LEDs stop blinking, press

YES

SYSTEM ERROR FIXED?

Enter 1111. The MIB board will display

13. Cycle the control power using the hidden reset switch behind the right control box again.

ENSURE

THE SWITCH IS HELD FOR 10 SECONDS. WAIT ANOTHER 20 SECONDS UNTIL THE MIB
BOARD HAS FULLY RESET BEFORE CONTINUING.

14.

With the computer displaying

OFF

, VERIFY software update by pressing the

TEMP

button to check

updated M3000/MIB/AIF/ATO version on each computer. IF ANY BOARDS DID NOT UPDATE,
REPEAT THE PROCESS STARTING WITH STEP 3.

Remove the SD card
using the

ngernail

slot on the top of the
card.

Insert the SD card

with contacts fac-

ing down.

Summary of Contents for LOV M3000



















































Search results

Summary of Contents for LOV M3000

Reviews:

Frymaster LOV M3000, Technical Reference Manual, Page: 21 / 50

Search results

Summary of Contents for LOV M3000

Reviews: