manualshive.com logo in svg

Frontier ST7526, Operator'S Manual

Share
Download
Frontier ST7526 Operator'S Manual Download Page 36

10. Remove the three 

fasteners

that hold the

friction wheel

to the

hub

(see Figure 50).

11. Remove the 

friction wheel

from the 

hub

. Slip the 

friction

wheel

off the 

hex shaft

.

12. Assemble the new 

friction wheel 

onto 

hub

with the fasteners

removed earlier.

13. Install the 

hex shaft

and 

bearings

with the four bolts removed

earlier (see Figure 51).

Make sure the washers are properly installed in the original
position. Also, make sure the two washers are properly
aligned with the actuator arms.

14. Make sure the 

hex shaft 

turns freely.

15. Install the right wheel, 

axle

, and 

drive sprocket

with the fas-

teners removed earlier. Install the 

chain

onto the 

drive sprock-

et

(see Figure 48).

16. Check the adjustment of the friction wheel. See “How To

Adjust The Friction Wheel” in this section. 

17. Make sure the friction wheel and the disc drive plate are free

from grease or oil.

18. Install the 

bottom panel 

(see Figure 47).

19. Tighten the 

bolts

on each side of the 

bottom panel

.

20. Install the 

left wheel 

to the 

axle

with the fasteners removed

earlier.

21. Connect the spark plug wire.

Figure 51

Washer

Bearings

Washer

Washer

Washer

Actuator Arms

Bearings

Hex Shaft

Figure 50

Fasteners

Hub

Friction

Wheel

Hex Shaft

Fasteners

MAINTENANCE

36

Summary of Contents for ST7526













































Reviews:

No comments

Brands by name

Popular brands

Load more brands