background image

OPERATION

20

MTF

051059L

TO STOP ENGINE

CAUTION: To stop the engine, do not move the choke

control to CHOKE position. Backfire or engine damage

can occur.

1. Move throttle control to SLOW, then to STOP

(Figure 17).

Figure 17

Throttle Control

2. Pull out safety/ignition key (Figure 18).

Figure 18

Throttle Control

TO START ENGINE

Be sure that engine has sufficient oil. Use a high quality

detergent oil classified “For Service SG, SH, SJ, SL, or

higher”.

The snow thrower engine is equipped with a 120 volt A.C.

electric starter and recoil starter.  Before starting the engine,

be certain that you have read the following information.

If engine floods, set the choke to the OPEN/RUN position and

crank until the engine starts.

WARNING: Rapid retraction of the starter cord

(kickback) will pull your hand or arm toward the

engine faster than you can let go of the starter

cord.

S

When starting the engine, slowly pull the starter cord

until  resistance is felt. Then, rapidly pull the starter

cord.

S

Make sure components; such as impellors, pulleys

or sprockets, are securely attached.

WARNING: The electric starter is equipped with

a three

wire power cord and plug designed to

operate on 120 volt AC house hold current. The

power cord must be properly grounded at all times to

avoid the possibility of electric shock which can cause

injury to the operator. Follow all instructions carefully

as set forth below:

Make sure your house has a three

wire grounded sys-

tem. If you are not sure, ask a licensed electrician. If

your house does not have a three

wire grounded sys-

tem, do not use this electric starter under any condi-

tion.

If your house has a three

wire grounded system but a

three hole receptacle is not available to connect the

electric starter, have a three

hole receptacle installed

by a licensed electrician.

WARNING: To connect a 120 volt power cord,

always connect the power cord first to the

switch box located on the engine and then plug

the other end into a three

hole grounded receptacle.

WARNING: To disconnect the power cord, al-

ways unplug the end connected to the three

hole grounded receptacle first.

COLD ENGINE START

(Engine has not been run recently.)
1. Be sure auger drive clutch lever and traction drive clutch

lever are in the disengaged (RELEASED) position.

2. Move throttle control to “FAST” position. Operate the en-

gine with the throttle control in FAST position (Figure 19).

Before engaging auger drive clutch lever allow engine to

idle for five minutes to allow engine oil to warm .  Failure

to allow engine oil to warm can cause damage to engine.

Figure 19

Throttle Control

3. Insert key into ignition slot. Make sure it snaps into place

(Figure 20). Do not turn key.

4. Rotate choke knob to the CHOKE position.
5. Push the primer button as follows:

Above 50

°

 F (10

°

 C), DO NOT PRIME.

From 50

°

 F (10

°

 C) to 15

°

F (

10

°

 C), PUSH TWO TIMES.

Below 15

°

 F (

10

°

 C), PUSH FOUR TIMES.

Summary of Contents for ST1332





























































Reviews: