Frontier SB1184 Operator'S Manual Download Page 38

Page: 38 / 52

MAINTENANCE

OM 0408SB1184-A

AVOIDABLE DAMAGES

POSSIBLE CAUSES

CORRECTIVE ACTIONS

ROSS



Cross arms broken.



Extreme torque peak or

shock load.



Axial loads too high.



Use appropriate safety device.



Change to a larger driveline

size.



Shorten driveline shaft.



Replace

defective

cross

bearings.



Bearing caps turning in their

cross journal.



Overheated bearing caps.



Excessive

continuous

torque and/or excessive
working angle.



Inadequate

greasing.



Verify compatibility between

shaft and working conditions.



Carefully

greasing

instructions.



Replace

defective

cross

bearings.



Accelerated wear of cross kit.



Excessive

continuous

torque and/or excessive
working angle.



Inadequate

greasing.



Verify compatibility between

shaft and working conditions.



Carefully

greasing

instructions.



Replace

defective

cross

bearings.

Note: Cross bearings must be greased every 8 working hours.

AVOIDABLE DAMAGES

POSSIBLE CAUSES

CORRECTIVE ACTIONS

ELESCOPIC

UBES



Telescopic tubes failure or

twisting.



Extreme torque peak or

shock load.



Short

tube

engagement.



Use appropriate safety device.



Change to a larger driveline

size.



Replace the driveline drive

shaft with one having
adequate length.



Replace

defective

tubes.

Accelerated wear of telescopic
tubes.



Extreme

load

when

sliding.



Short

tube

engagement.



Inadequate

greasing.



Dirt



Change to a driveline with

rilsan coated inner tube.



Replace the driveline with one

having adequate length.



Carefully

greasing

instructions.



Replace

defective

tubes.

Note: Telescopic tubes must be cleaned and greased every 8 working hours.

Summary of Contents for SB1184




















































Search results

Summary of Contents for SB1184

Reviews:

Brands by name

Popular brands

Frontier SB1184, Operator'S Manual

Search results

Summary of Contents for SB1184

Reviews:

Brands by name

Popular brands